Infiniti EX35. Manual — part 348
WHEEL SENSOR
BRC-107
< ON-VEHICLE REPAIR >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
ON-VEHICLE REPAIR
WHEEL SENSOR
FRONT WHEEL SENSOR
FRONT WHEEL SENSOR : Exploded View
INFOID:0000000003133001
NOTE:
The above figure shows left side. Right side is the mirror image.
FRONT WHEEL SENSOR : Removal and Installation
INFOID:0000000003133002
REMOVAL
Be careful with the following when removing sensor.
CAUTION:
• Do not twist sensor harness as much as possible, when removing it. Pull sensors out without pulling
sensor harness.
• Be careful to avoid damaging sensor edges or rotor teeth. Remove wheel sensor first before remov-
ing front or rear wheel hub. This is to avoid damage to sensor wiring and loss of sensor function.
INSTALLATION
Be careful with the following when installing wheel sensor. Tighten installation bolts to the specified torques.
Refer to
BRC-107, "FRONT WHEEL SENSOR : Exploded View"
.
CAUTION:
• When installing, make sure there is no foreign material such as iron chips on and in the mounting
hole of the wheel sensor. Make sure no foreign material has been caught in the sensor rotor. Remove
any foreign material and clean the mount.
1.
Front LH wheel sensor connector
2.
Front LH wheel sensor
3.
Bracket
A.
White line (slant line)
: Vehicle front
Refer to GI section
for symbol marks in the figure.
JSFIA0194GB
BRC-108
< ON-VEHICLE REPAIR >
[VDC/TCS/ABS]
WHEEL SENSOR
• When installing wheel sensor, be sure to press rubber grommets in until they lock at locations
shown above in the figure. When installed, harness must not be twisted.
• When you see the harness of the wheel sensor from the front side of the vehicle ensure that the
white lines (A) are not twisted.
REAR WHEEL SENSOR
REAR WHEEL SENSOR : Exploded View
INFOID:0000000003291967
REAR WHEEL SENSOR : Removal and Installation
INFOID:0000000003291968
REMOVAL
Be careful with the following when removing sensor.
CAUTION:
• Do not twist sensor harness as much as possible, when removing it. Pull sensors out without pulling
sensor harness.
• Be careful to avoid damaging sensor edges or rotor teeth. Remove wheel sensor first before remov-
ing front or rear wheel hub. This is to avoid damage to sensor wiring and loss of sensor function.
INSTALLATION
Be careful with the following when installing wheel sensor. Tighten installation bolts to the specified torques.
Refer to
BRC-108, "REAR WHEEL SENSOR : Exploded View"
.
CAUTION:
• When installing, make sure there is no foreign material such as iron chips on and in the mounting
hole of the wheel sensor. Make sure no foreign material has been caught in the sensor rotor. Remove
any foreign material and clean the mount.
• When installing a rear LH wheel sensor, be sure to pass the wheel sensor harness under the breather
hose.
1.
Rear LH wheel sensor
2.
Rear LH wheel sensor connector
3.
Rear RH wheel sensor connector
4.
Rear RH wheel sensor
: Vehicle front
Refer to GI section
for symbol marks in the figure.
JSFIA0195GB
SENSOR ROTOR
BRC-109
< ON-VEHICLE REPAIR >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
SENSOR ROTOR
FRONT SENSOR ROTOR
FRONT SENSOR ROTOR : Exploded View
INFOID:0000000003133003
(2WD models),
(AWD models).
FRONT SENSOR ROTOR : Removal and Installation
INFOID:0000000003133004
REMOVAL
Sensor rotor cannot be disassembled. Remove the sensor rotor together with hub bearing assembly. Refer to
(2WD models),
(AWD models).
INSTALLATION
Sensor rotor cannot be disassembled. Install the sensor rotor together with hub bearing assembly. Refer to
(2WD models),
(AWD models).
REAR SENSOR ROTOR
REAR SENSOR ROTOR : Exploded View
INFOID:0000000003133005
REAR SENSOR ROTOR : Removal and Installation
INFOID:0000000003133006
REMOVAL
• Follow the procedure below to remove rear sensor rotor.
- Remove side flange. Refer to
.
- Using a bearing replacer (suitable tool) and puller (suitable tool), remove sensor rotor from side flange.
INSTALLATION
CAUTION:
Do not reuse sensor rotor.
• Follow the procedure below to install rear sensor rotor.
- Using a drifts, press rear sensor rotor onto side flange.
- Install side flange. Refer to
1.
Side flange
2.
Rear wheel sensor rotor
Refer to GI section
for symbol marks in the figure.
JSFIA0054JP
A: Drift [SST: ST30720000 (J-25405)]
B: Drift [SST: ST27863000 (
—
)]
C: Drift [SST: KV40104710 (
—
)]
SFIA3387E
BRC-110
< ON-VEHICLE REPAIR >
[VDC/TCS/ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Exploded View
INFOID:0000000003133007
Removal and Installation
INFOID:0000000003133008
REMOVAL
CAUTION:
• Before servicing, disconnect the battery cable from negative terminal.
• To remove brake tube, use a flare nut wrench to prevent flare nuts and brake tube from being dam-
aged. To install, use flare nut crowfoot and torque wrench.
• Do not apply excessive impact to ABS actuator and electric unit (control unit), such as dropping it.
• Do not remove and install actuator by holding harness.
• After work is completed, bleed air from brake tube. Refer to
BR-11, "Bleeding Brake System"
1.
Remove hoodledge cover (LH). Refer to
2.
Disconnect ABS actuator and electric unit (control unit) connector.
3.
Loosen brake tube flare nuts, then remove brake tubes from ABS actuator and electric unit (control unit).
4.
Remove tire (front LH side).
5.
Remove fender protector (rear): (front LH side). Refer to
EXT-25, "FENDER PROTECTOR : Exploded
.
6.
Remove ABS actuator and electric unit (control unit) bracket mounting nuts.
7.
Remove ABS actuator and electric unit (control unit) from vehicle.
1.
ABS actuator and electric unit (control
unit)
2.
Connector
3.
Bushing
4.
Bracket
A.
From master cylinder secondary side B.
From master cylinder primary side
C.
To front LH brake caliper
D.
To rear RH brake caliper
E.
To Rear LH brake caliper
F.
To front RH brake caliper
: Vehicle front
Refer to GI section
for symbol marks in the figure.
JSFIA0196GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст