Infiniti EX35. Manual — part 1418
TM-60
< COMPONENT DIAGNOSIS >
[5AT: RE5R05A]
P0732 A/T 2ND GEAR FUNCTION
P0732 A/T 2ND GEAR FUNCTION
Description
INFOID:0000000003130496
This malfunction is detected when the A/T does not shift into 2nd gear position as instructed by TCM. This is
not only caused by electrical malfunction (circuits open or shorted) but by mechanical malfunction such as
control valve sticking, improper solenoid valve operation, etc.
DTC Logic
INFOID:0000000003130497
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF. Then wait at least 10 seconds before performing the next test.
1.
CHECK ATF TEMPERATURE
With CONSULT-III
1.
Start the engine.
2.
Select “Data Monitor” mode for “TRANSMISSION”.
3.
Check ATF temperature is in the following range.
With GST
1.
Start the engine.
2.
Drive vehicle for approximately 5 minutes in urban areas, GO TO 2.
Is ATF temperature within specified range?
YES
>> GO TO 2.
NO
>> Drive vehicle to warm ATF or stop engine to cool ATF.
2.
CHECK SYMPTOM 1
With CONSULT-III
1.
Select “DTC & SRT Confirmation” for “TRANSMISSION”.
2.
Select “2ND GR FNCTN P0732” of “DTC WORK SUPPORT” mode.
3.
Drive vehicle and maintain the following conditions.
DTC
Item
(CONSULT-III screen
terms)
A/T CHECK indicator
lamp judgment flicker
Diagnostic item is de-
tected when...
Possible cause
P0732
A/T 2ND GR FNCTN
19th
TCM detects any incon-
sistency in the actual
gear ratio.
• Input clutch solenoid
valve
• Front brake solenoid
valve
• Direct clutch solenoid
valve
• High and low reverse
clutch solenoid valve
• Each clutch and brake
• Hydraulic control cir-
cuit
ATF TEMP 1
: 20
°
C (68
°
F) – 140
°
C (284
°
F)
MANU MODE SW
: ON
GEAR
: “2” position
ACCELE POSI
: 0.6/8 or more
VEHICLE SPEED
: 10 km/h (6 MPH) or more
P0732 A/T 2ND GEAR FUNCTION
TM-61
< COMPONENT DIAGNOSIS >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
Keep the current driving status for at least 5 consecutive seconds if CONSULT-III screen changes from
“OUT OF CONDITION” to “TESTING”.
CAUTION:
If “TESTING” does not appear on CONSULT-III for a long time, select “Self Diagnostic Results”
mode for “TRANSMISSION”. In case a 1st trip DTC other than “P0732 A/T 2ND GR FNCTN” is
shown, refer to “SELF DIAGNOSTIC RESULTS”. Refer to
TM-40, "CONSULT-III Function (TRANS-
With GST
1.
Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.
2.
Check DTC.
Is “STOP VEHICLE” or “COMPLETED RESULT NG” displayed? / Is “P0732 A/T 2ND GR FNCTN” detected?
YES-1 >> “STOP VEHICLE”: GO TO 3.
YES-2 >> “COMPLETED RESULT NG”: Go to
YES-3 >> “P0732 A/T 2ND GR FNCTN” is detected: Go to
NO
>> Check intermittent incident. Refer to
GI-38, "Intermittent Incident"
.
3.
CHECK SYMPTOM 2
With CONSULT-III
1.
Stop vehicle.
2.
Drive vehicle in “D” position allowing it to shift from 1st to 5th gear and check shift timing and shift shock.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-38, "Intermittent Incident"
.
NO
>> Confirm malfunction phenomena by “ROAD TEST” to repair malfunctioning part. Refer to
Diagnosis Procedure
INFOID:0000000003130498
1.
CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts.
2.
REPLACE CONTROL VALVE WITH TCM
1.
Replace control valve with TCM. Refer to
.
2.
Perform “DTC CONFIRMATION PROCEDURE”. Refer to
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Confirm malfunction phenomena by “ROAD TEST” to repair malfunctioning part. Refer to
ENGINE SPEED
: TURBINE REV
−
50 rpm or more
TURBINE REV
: 300 rpm or more
Manual mode switch
: ON
Gear position
: “2” position
Accelerator opening
: 0.6/8 or more
Vehicle speed
: 10 km/h (6 MPH) or more
TM-62
< COMPONENT DIAGNOSIS >
[5AT: RE5R05A]
P0733 A/T 3RD GEAR FUNCTION
P0733 A/T 3RD GEAR FUNCTION
Description
INFOID:0000000003130499
This malfunction is detected when the A/T does not shift into 3rd gear position as instructed by TCM. This is
not only caused by electrical malfunction (circuits open or shorted) but by mechanical malfunction such as
control valve sticking, improper solenoid valve operation, etc.
DTC Logic
INFOID:0000000003130500
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF. Then wait at least 10 seconds before performing the next test.
1.
CHECK ATF TEMPERATURE
With CONSULT-III
1.
Start the engine.
2.
Select “Data Monitor” mode for “TRANSMISSION”.
3.
Check ATF temperature is in the following range.
With GST
1.
Start the engine.
2.
Drive vehicle for approximately 5 minutes in urban areas, GO TO 2.
Is ATF temperature within specified range?
YES
>> GO TO 2.
NO
>> Drive vehicle to warm ATF or stop engine to cool ATF.
2.
CHECK SYMPTOM 1
With CONSULT-III
1.
Select “DTC & SRT Confirmation” for “TRANSMISSION”.
2.
Select “3RD GR FNCTN P0733” of “DTC WORK SUPPORT” mode.
3.
Drive vehicle and maintain the following conditions.
DTC
Item
(CONSULT-III screen
terms)
A/T CHECK indicator
lamp judgment flicker
Diagnostic item is de-
tected when...
Possible cause
P0733
A/T 3RD GR FNCTN
20th
TCM detects any incon-
sistency in the actual
gear ratio.
• Input clutch solenoid
valve
• Front brake solenoid
valve
• Direct clutch solenoid
valve
• High and low reverse
clutch solenoid valve
• Each clutch and brake
• Hydraulic control cir-
cuit
ATF TEMP 1
: 20
°
C (68
°
F) – 140
°
C (284
°
F)
MANU MODE SW
: ON
GEAR
: “3” position
ACCELE POSI
: 0.6/8 or more
VEHICLE SPEED
: 10 km/h (6 MPH) or more
P0733 A/T 3RD GEAR FUNCTION
TM-63
< COMPONENT DIAGNOSIS >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
Keep the current driving status for at least 5 consecutive seconds if CONSULT-III screen changes from
“OUT OF CONDITION” to “TESTING”.
CAUTION:
If “TESTING” does not appear on CONSULT-III for a long time, select “Self Diagnostic Results”
mode for “TRANSMISSION”. In case a 1st trip DTC other than “P0733 A/T 3RD GR FNCTN” is
shown, refer to “SELF DIAGNOSTIC RESULTS”. Refer to
TM-40, "CONSULT-III Function (TRANS-
With GST
1.
Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.
2.
Check DTC.
Is “STOP VEHICLE” or “COMPLETED RESULT NG” displayed? / Is “P0733 A/T 3RD GR FNCTN” detected?
YES-1 >> “STOP VEHICLE”: GO TO 3.
YES-2 >> “COMPLETED RESULT NG”: Go to
YES-3 >> “P0733 A/T 3RD GR FNCTN” is detected: Go to
NO
>> Check intermittent incident. Refer to
GI-38, "Intermittent Incident"
.
3.
CHECK SYMPTOM 2
With CONSULT-III
1.
Stop vehicle.
2.
Drive vehicle in “D” position allowing it to shift from 1st to 5th gear and check shift timing and shift shock.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-38, "Intermittent Incident"
.
NO
>> Confirm malfunction phenomena by “ROAD TEST” to repair malfunctioning part. Refer to
Diagnosis Procedure
INFOID:0000000003130501
1.
CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts.
2.
REPLACE CONTROL VALVE WITH TCM
1.
Replace control valve with TCM. Refer to
.
2.
Perform “DTC CONFIRMATION PROCEDURE”. Refer to
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Confirm malfunction phenomena by “ROAD TEST” to repair malfunctioning part. Refer to
ENGINE SPEED
: TURBINE REV
−
50 rpm or more
TURBINE REV
: 300 rpm or more
Manual mode switch
: ON
Gear position
: “3” position
Accelerator opening
: 0.6/8 or more
Vehicle speed
: 10 km/h (6 MPH) or more
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст