Infiniti EX35. Manual — part 1419
TM-64
< COMPONENT DIAGNOSIS >
[5AT: RE5R05A]
P0734 A/T 4TH GEAR FUNCTION
P0734 A/T 4TH GEAR FUNCTION
Description
INFOID:0000000003130502
This malfunction is detected when the A/T does not shift into 4th gear position as instructed by TCM. This is
not only caused by electrical malfunction (circuits open or shorted) but by mechanical malfunction such as
control valve sticking, improper solenoid valve operation, etc.
DTC Logic
INFOID:0000000003130503
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF. Then wait at least 10 seconds before performing the next test.
1.
CHECK ATF TEMPERATURE
With CONSULT-III
1.
Start the engine.
2.
Select “Data Monitor” mode for “TRANSMISSION”.
3.
Check ATF temperature is in the following range.
With GST
1.
Start the engine.
2.
Drive vehicle for approximately 5 minutes in urban areas, GO TO 2.
Is ATF temperature within specified range?
YES
>> GO TO 2.
NO
>> Drive vehicle to warm ATF or stop engine to cool ATF.
2.
CHECK SYMPTOM 1
With CONSULT-III
1.
Select “DTC & SRT Confirmation” for “TRANSMISSION”.
2.
Select “4TH GR FNCTN P0734” of “DTC WORK SUPPORT” mode.
3.
Drive vehicle and maintain the following conditions.
DTC
Item
(CONSULT-III screen
terms)
A/T CHECK indicator
lamp judgment flicker
Diagnostic item is de-
tected when...
Possible cause
P0734
A/T 4TH GR FNCTN
21st
TCM detects any incon-
sistency in the actual
gear ratio.
• Input clutch solenoid
valve
• Front brake solenoid
valve
• Direct clutch solenoid
valve
• High and low reverse
clutch solenoid valve
• Each clutch and brake
• Hydraulic control cir-
cuit
ATF TEMP 1
: 20
°
C (68
°
F) – 140
°
C (284
°
F)
MANU MODE SW
: ON
GEAR
: “4” position
ACCELE POSI
: 0.6/8 or more
VEHICLE SPEED
: 10 km/h (6 MPH) or more
P0734 A/T 4TH GEAR FUNCTION
TM-65
< COMPONENT DIAGNOSIS >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
Keep the current driving status for at least 5 consecutive seconds if CONSULT-III screen changes from
“OUT OF CONDITION” to “TESTING”.
CAUTION:
If “TESTING” does not appear on CONSULT-III for a long time, select “Self Diagnostic Results”
mode for “TRANSMISSION”. In case a 1st trip DTC other than “P0734 A/T 4TH GR FNCTN” is
shown, refer to “SELF DIAGNOSTIC RESULTS”. Refer to
TM-40, "CONSULT-III Function (TRANS-
With GST
1.
Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.
2.
Check DTC.
Is “STOP VEHICLE” or “COMPLETED RESULT NG” displayed? / Is “P0734 A/T 4TH GR FNCTN” detected?
YES-1 >> “STOP VEHICLE”: GO TO 3.
YES-2 >> “COMPLETED RESULT NG”: Go to
YES-3 >> “P0734 A/T 4TH GR FNCTN” is detected: Go to
.
NO
>> Check intermittent incident. Refer to
GI-38, "Intermittent Incident"
.
3.
CHECK SYMPTOM 2
With CONSULT-III
1.
Stop vehicle.
2.
Drive vehicle in “D” position allowing it to shift from 1st to 5th gear and check shift timing and shift shock.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-38, "Intermittent Incident"
.
NO
>> Confirm malfunction phenomena by “ROAD TEST” to repair malfunctioning part. Refer to
Diagnosis Procedure
INFOID:0000000003130504
1.
CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts.
2.
REPLACE CONTROL VALVE WITH TCM
1.
Replace control valve with TCM. Refer to
.
2.
Perform “DTC CONFIRMATION PROCEDURE”. Refer to
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Confirm malfunction phenomena by “ROAD TEST” to repair malfunctioning part. Refer to
ENGINE SPEED
: TURBINE REV
−
50 rpm or more
TURBINE REV
: 300 rpm or more
Manual mode switch
: ON
Gear position
: “4” position
Accelerator opening
: 0.6/8 or more
Vehicle speed
: 10 km/h (6 MPH) or more
TM-66
< COMPONENT DIAGNOSIS >
[5AT: RE5R05A]
P0735 A/T 5TH GEAR FUNCTION
P0735 A/T 5TH GEAR FUNCTION
Description
INFOID:0000000003130505
This malfunction is detected when the A/T does not shift into 5th gear position as instructed by TCM. This is
not only caused by electrical malfunction (circuits open or shorted) but by mechanical malfunction such as
control valve sticking, improper solenoid valve operation, etc.
DTC Logic
INFOID:0000000003130506
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF. Then wait at least 10 seconds before performing the next test.
1.
CHECK ATF TEMPERATURE
With CONSULT-III
1.
Start the engine.
2.
Select “Data Monitor” mode for “TRANSMISSION”.
3.
Check ATF temperature is in the following range.
With GST
1.
Start the engine.
2.
Drive vehicle for approximately 5 minutes in urban areas, GO TO 2.
Is ATF temperature within specified range?
YES
>> GO TO 2.
NO
>> Drive vehicle to warm ATF or stop engine to cool ATF.
2.
CHECK SYMPTOM 1
With CONSULT-III
1.
Select “DTC & SRT Confirmation” for T“RANSMISSION”.
2.
Select “5TH GR FNCTN P0735” of “DTC WORK SUPPORT” mode.
3.
Drive vehicle and maintain the following conditions.
DTC
Item
(CONSULT-III screen
terms)
A/T CHECK indicator
lamp judgment flicker
Diagnostic item is de-
tected when...
Possible cause
P0735
A/T 5TH GR FNCTN
22nd
TCM detects any incon-
sistency in the actual
gear ratio.
• Input clutch solenoid
valve
• Front brake solenoid
valve
• Direct clutch solenoid
valve
• High and low reverse
clutch solenoid valve
• Each clutch and brake
• Hydraulic control cir-
cuit
ATF TEMP 1
: 20
°
C (68
°
F) – 140
°
C (284
°
F)
MANU MODE SW
: ON
GEAR
: “5” position
ACCELE POSI
: 0.6/8 or more
VEHICLE SPEED
: 10 km/h (6 MPH) or more
P0735 A/T 5TH GEAR FUNCTION
TM-67
< COMPONENT DIAGNOSIS >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
Keep the current driving status for at least 5 consecutive seconds if CONSULT-III screen changes from
“OUT OF CONDITION” to “TESTING”.
CAUTION:
If “TESTING” does not appear on CONSULT-III for a long time, select “Self Diagnostic Results”
mode for “TRANSMISSION”. In case a 1st trip DTC other than “P0735 A/T 5TH GR FNCTN” is
shown, refer to “SELF DIAGNOSTIC RESULTS”. Refer to
TM-40, "CONSULT-III Function (TRANS-
With GST
1.
Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.
2.
Check DTC.
Is “STOP VEHICLE” or “COMPLETED RESULT NG” displayed? / Is “P0735 A/T 5TH GR FNCTN” detected?
YES-1 >> “STOP VEHICLE”: GO TO 3.
YES-2 >> “COMPLETED RESULT NG”: Go to
YES-3 >> “P0735 A/T 5TH GR FNCTN” is detected: Go to
.
NO
>> Check intermittent incident. Refer to
GI-38, "Intermittent Incident"
.
3.
CHECK SYMPTOM 2
With CONSULT-III
1.
Stop vehicle.
2.
Drive vehicle in “D” position allowing it to shift from 1st to 5th gear and check shift timing and shift shock.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-38, "Intermittent Incident"
.
NO
>> Confirm malfunction phenomena by “ROAD TEST” to repair malfunctioning part. Refer to
Diagnosis Procedure
INFOID:0000000003130507
1.
CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts.
2.
REPLACE CONTROL VALVE WITH TCM
1.
Replace control valve with TCM. Refer to
2.
Perform “DTC CONFIRMATION PROCEDURE”. Refer to
.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Confirm malfunction phenomena by “ROAD TEST” to repair malfunctioning part. Refer to
ENGINE SPEED
: TURBINE REV
−
50 rpm or more
TURBINE REV
: 300 rpm or more
Manual mode switch
: ON
Gear position
: “5” position
Accelerator opening
: 0.6/8 or more
Vehicle speed
: 10 km/h (6 MPH) or more
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст