Infiniti EX35. Manual — part 839
ROOF RAIL
EXT-35
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
3.
Insert a remover tool (A) into outside space.
4.
Remove front roof rail cover (1) inside pawls with remover tool
(B).
5.
Pull front roof rail cover (1) toward the arrow direction.
6.
Insert a remover tool (A) into rear space.
7.
Remove rear roof rail cover (1) outside pawls with remover tool
(B).
CAUTION:
Apply protective tape (C) around the roof rail.
8.
Insert a remover tool (A) into outside space.
9.
Remove rear roof rail cover (1) inside pawls with remover tool
(B).
10. Pull rear roof rail cover (1) toward the arrow direction.
: Pawl
JMKIA2198ZZ
JMKIA2199ZZ
: Pawl
JMKIA2200ZZ
: Pawl
JMKIA2201ZZ
JMKIA2202ZZ
EXT-36
< ON-VEHICLE REPAIR >
ROOF RAIL
11. Remove roof rail assembly mounting bolts, and then remove roof rail assembly.
INSTALLATION
Install in the reverse order of removal.
ROOF SIDE MOLDING
EXT-37
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
ROOF SIDE MOLDING
Exploded View
INFOID:0000000003671644
Removal and Installation
INFOID:0000000003671645
REMOVAL
1.
Remove front fender cover (LH/RH). Refer to
.
2.
Disengage clips while pinching molding from roof rear end to
front end.
INSTALLATION
1.
Roof side molding
2.
Molding fastener (upper)
3.
Molding fastener (lower)
4.
Rivet
5.
Roof side molding clip
6.
Body side panel
7.
Roof panel
: Clip
Refer to
JMKIA2203ZZ
PIIB2749J
EXT-38
< ON-VEHICLE REPAIR >
ROOF SIDE MOLDING
Install from roof side molding rear end to front end in this order after temporarily holding.
REMOVAL AND INSTALLATION OF ROOF SIDE MOLDING CLIP
Removal
1.
Remove roof side molding.
2.
Heat adhesive tape interface using a dryer, and then peel roof side molding clips (body side) using long-
nose pliers.
CAUTION:
Be careful not to damage the body.
Installation
1.
Clean tape removed surface with a shop cloth soaked in white gasoline or IPA.
2.
Use two-part epoxy adhesive.
3.
Apply adhesive evenly to clip tape surface.
4.
Position applied parts to the proper location, and then sufficiently press-fit until the adhesive protrudes to
tape side.
5.
Tape clips after press fit, and temporarily hold it for specified time based on the following.
6.
Install from roof side molding rear end to front end in this order after temporarily holding.
CAUTION:
• Use double-faced adhesive tape after hardening for clips.
• Securely insert molding rear end cap onto roof rear end cutout (installation standard).
• When installing roof side molding of windshield portion, check that molding fastener is securely
inserted and then press in.
• Do not wash the vehicle with in 24 hours so as to keep adhesive.
Adhesive
: 3M-weld DP–100 or equivalent
Thickness
: Approximately 0.5 mm (0.020 in)
Press-fit limit
: 19.6 N (2.0 Kg - 4.41 lb)
×
2 seconds
5 to 10
°
C (41 to 50
°
F)
: 1 hour or more
11 to 23
°
C (52 to 73
°
F)
: 30 minutes or more
24
°
C or more (75
°
F or more)
: 15 minutes or more
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст