Infiniti EX35. Manual — part 395
CCS
INSPECTION AND ADJUSTMENT
CCS-115
< BASIC INSPECTION >
[LDW & LDP]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
1.
CHECK VEHICLE HEIGHT
Measure the wheelarch height. Calculate “Dh”.
NOTE:
“Dh” may be calculated as a minus value.
>> GO TO 2.
2.
CAMERA AIMING ADJUSTMENT
CONSULT-III WORK SUPPORT
CAUTION:
Operate CONSULT-III outside the vehicle, and close all the doors. (To retain vehicle attitude appropri-
ately)
1.
Select “Work Support” on “LANE CAM” with CONSULT-III.
2.
Select “AUTO AIM”.
3.
Confirm the following items;
-
The target should be accurately placed.
-
The vehicle should be stopped.
4.
Select “Start” to perform camera aiming.
CAUTION:
Never select “Start” when the target is not accurately placed.
5.
Input “Dh”, and then select “Start”.
CAUTION:
Never change “Ht” and “Dt”.
6.
Confirm the displayed item.
-
“Normally Completed”: Select “Completion”.
-
“SUSPENSION” or “ABNORMALLY COMPLETED”: Perform the following services.
NOTE:
Replace camera unit if “SUSPENSION” is repeatedly indicated during the above two services are performed.
7.
Confirm that “Normally Completed” is displayed and then select “End” to close the aiming adjustment pro-
cedure.
>> GO TO 3.
3.
PERFORM SELF-DIAGNOSIS
Perform self-diagnosis of lane camera unit with CONSULT-III.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the applicable item. Refer to
.
NO
>> GO TO 4.
4.
ACTION TEST
Test the LDW/LDP system operation by action test. Refer to
>> WORK END
Dh [mm] = (Hfl + Hfr)
÷
2
−
747
where,
Hfl: Front left wheelarch height [mm]
Hfr: Front right wheelarch height [mm]
JPMIA0929ZZ
Displayed item
Service procedure
SUSPENSION
00H Routine not activated
Position the target appropriately again. Perform the aiming again.
Refer to
CCS-113, "CAMERA AIMING ADJUSTMENT : Special Re-
pair Requirement (Target Setting)"
10H Writing error
ABNORMALLY COMPLETED
—
CCS-116
< BASIC INSPECTION >
[LDW & LDP]
INSPECTION AND ADJUSTMENT
CAMERA AIMING ADJUSTMENT : Special Repair Requirement (Target Mark Sample)
INFOID:0000000003514567
NOTE:
Print this illustration so that the diameter of the circle is 200 mm (7.87 in).
PGIA0105J
CCS
LANE DEPARTURE WARNING (LDW) SYSTEM
CCS-117
< FUNCTION DIAGNOSIS >
[LDW & LDP]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
FUNCTION DIAGNOSIS
LANE DEPARTURE WARNING (LDW) SYSTEM
System Diagram
INFOID:0000000003514568
System Description
INFOID:0000000003514569
OUTLINE
• Lane Departure Warning (LDW) system provides a lane departure warning function when the vehicle is
driven at speeds of approximately 72 km/h (45 MPH) or more.
• When the vehicle approaches either the left or the right side of the traveling lane, a warning will sound and
the lane departure warning lamp (yellow) on the combination meter will blink to alert the driver.
• The warning function will stop when the vehicle returns inside of the lane markers.
BASIC OPERATIONS
Switches And Indicator/Warning Lamps
JPMIA0928GB
JPOIA0014GB
CCS-118
< FUNCTION DIAGNOSIS >
[LDW & LDP]
LANE DEPARTURE WARNING (LDW) SYSTEM
Bulb Check Action and Fail-safe Indication
LDW INITIAL STATE CHANGE
CAUTION:
Never change LDW initial state “ON”
⇒
“OFF” without the consent of the customer.
LDW initial state can be changed.
• LDW initial ON* - LDW function is automatically turned ON, when the ignition switch OFF
⇒
ON.
• LDW initial OFF - LDW function is still OFF when the ignition switch OFF
⇒
ON.
*: Factory setting
How to change LDW initial state
1.
Turn ignition switch ON.
2.
Switch LDW and LDP functions to OFF.
3.
Push and hold LDW switch for more than 4 seconds.
4.
Buzzer sounds and blinking of the lane departure warning lamp informs that the LDW initial state change
is completed.
1.
LDW switch
2.
LDW ON indicator
3.
Lane departure warning lamp
(Yellow)
A.
On the instrument driver lower panel
B.
On the combination meter
JPOIA0031ZZ
Vehicle condition/ Driver's operation
LDW ON indi-
cator
Indication on the combination meter
Ignition switch:
OFF
⇒
ON
2 sec. ON
When DTC is detected
(Except “C1B01” and “C1B03”)
ON
Camera aiming is not completed
(“C1B01” is detected)
ON
Temporary disabled status at high temperature
(“C1B03” is detected)
Blink
OFF
JPOIA0017GB
JPOIA0019GB
JPOIA0020GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст