Infiniti EX35. Manual — part 1560
WW-92
< ECU DIAGNOSIS >
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.
STARTER MOTOR PROTECTION FUNCTION
IPDM E/R turns OFF the starter control relay to protect the starter motor when the starter control relay remains
active for 90 seconds.
DTC Index
INFOID:0000000003769980
NOTE:
• The details of time display are as follows.
- CRNT: A malfunction is detected now
- PAST: A malfunction was detected in the past.
• IGN counter is displayed on FFD (Freeze Frame data).
- The number is 0 when is detected now
- The number increases like 1
→
2 ··· 38
→
39 after returning to the normal condition whenever IGN OFF
→
ON.
- The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
×
: Applicable
Ignition switch
Front wiper switch
Front wiper auto stop signal
ON
OFF
The front wiper auto stop signal (stop posi-
tion) cannot be input for 10 seconds.
ON
The front wiper auto stop signal does not
change for 10 seconds.
CONSULT display
Fail-safe
Reference
No DTC is detected.
further testing
may be required.
—
—
U1000: CAN COMM CIRCUIT
×
B2098: IGN RELAY ON
×
B2099: IGN RELAY OFF
—
B2108: STRG LCK RELAY ON
—
B2109: STRG LCK RELAY OFF
—
B210A: STRG LCK STATE SW
—
B210B: START CONT RLY ON
—
B210C: START CONT RLY OFF
—
B210D: STARTER RELAY ON
—
B210E: STARTER RELAY OFF
—
B210F: INTRLCK/PNP SW ON
—
B2110: INTRLCK/PNP SW OFF
—
WIPER AND WASHER SYSTEM SYMPTOMS
WW-93
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
SYMPTOM DIAGNOSIS
WIPER AND WASHER SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000003591483
CAUTION:
Perform the self-diagnosis with CONSULT-III before performing the diagnosis by symptom. Perform
the diagnosis by DTC if DTC is detected.
Symptom
Probable malfunction location
Inspection item
Front wiper does not
operate.
HI only
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
• IPDM E/R
• Harness between IPDM E/R and front wiper
motor
• Front wiper motor
Front wiper motor (HI) circuit
Refer to
.
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R DATA MONITOR
“FR WIP REQ”
LO and INT
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
• IPDM E/R
• Harness between IPDM E/R and front wiper
motor
• Front wiper motor
Front wiper motor (LO) circuit
Refer to
.
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R DATA MONITOR
“FR WIP REQ”
INT only
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R DATA MONITOR
“FR WIP REQ”
HI, LO and INT
SYMPTOM DIAGNOSIS
“FRONT WIPER DOES NOT OPERATE”
Refer to
.
WW-94
< SYMPTOM DIAGNOSIS >
WIPER AND WASHER SYSTEM SYMPTOMS
Front wiper does not
stop.
HI only
• Combination switch
• BCM
Combination switch
Refer to
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R DATA MONITOR
“FR WIP REQ”
IPDM E/R
—
LO only
• Combination switch
• BCM
Combination switch
Refer to
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R DATA MONITOR
“FR WIP REQ”
IPDM E/R
—
INT only
• Combination switch
• BCM
Combination switch
Refer to
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R DATA MONITOR
“FR WIP REQ”
Front wiper does not
operate normally.
Intermittent adjustment
cannot be performed.
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
BCM
—
Intermittent control
linked with vehicle
speed cannot be per-
formed.
Check the vehicle speed detection wiper setting.
Refer to
WW-14, "WIPER : CONSULT-III Function (BCM - WIPER)"
NOTE:
Factory setting of the front wiper intermitted operation is the operation without ve-
hicle speed.
Wiper is not linked to
the washer operation.
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
BCM
—
Does not return to stop
position [Repeatedly
operates for 10 sec-
onds and then stops
for 20 seconds. After
that, it stops the opera-
tion. (Fail-safe)]
• IPDM E/R
• Harness between IPDM E/R and front wiper
motor
• Front wiper motor
Front wiper auto stop signal
circuit
Refer to
.
Rear wiper does not
operate.
ON only
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
INT only
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
ON and INT
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
• BCM
• Harness between rear wiper motor and BCM
• Harness between rear wiper motor and ground
• Rear wiper motor
Combination switch
Refer to
Symptom
Probable malfunction location
Inspection item
WIPER AND WASHER SYSTEM SYMPTOMS
WW-95
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Rear wiper does not
stop.
ON only
• Combination switch
• BCM
Rear wiper motor circuit
Refer to
.
INT only
• Combination switch
• BCM
Combination switch
Refer to
Rear wiper does not
operate normally.
Wiper is not linked to
the washer operation.
• Combination switch
• Harness between rear wiper motor and BCM
• BCM
Combination switch
Refer to
BCM
—
Rear wiper does not
return to the stop posi-
tion [Stops after a five-
second operation.
(Fail-safe)]
• BCM
• Harness between rear wiper motor and BCM
• Rear wiper motor
Rear wiper auto stop signal
circuit
Refer to
.
Symptom
Probable malfunction location
Inspection item
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст