Infiniti EX35. Manual — part 833
PREPARATION
EXT-11
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000003134281
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000003134282
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Location the noise
(J-43980)
NISSAN Squeak and Rattle
Kit
Repairing the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locating the noise
Remover tool
Remove clips, pawls, metal clips
Power tool
SIIA0995E
PIIB7923J
PIIB1407E
EXT-12
< ON-VEHICLE REPAIR >
FRONT BUMPER
ON-VEHICLE REPAIR
FRONT BUMPER
Exploded View
INFOID:0000000003134283
JMKIA2137ZZ
FRONT BUMPER
EXT-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation
INFOID:0000000003134284
REMOVAL
CAUTION:
Bumper fascia is made of resin. Do not apply strong force to it, and be careful to prevent contact with
oil.
1.
Fully open hood assembly.
2.
Remove clips (A) of front bumper fascia upper side.
3.
Remove front fillet molding (1) fixing screws (A) (LH/RH).
4.
Remove front fillet molding fixing pawls and clip (LH/RH).
Refer to
EXT-32, "Removal and Installation"
.
5.
Remove fender protector (1) fixing clip (A) and grommet (B) (LH/
RH).
1.
Grommet
2.
Bumper side bracket RH
3.
Front grille
4.
Bumper side grommet RH
5.
Bumper fascia assembly
6.
Fog lamp finisher RH
7.
Sonar sensor RH
8.
Front fog lamp RH
9.
License plate bracket
10. Bumper bracket cover
11.
Bumper finisher RH
12. Bumper finisher LH (with ICC)
13. Front fog lamp LH
14.
Bumper finisher LH (without ICC)
15. Sonar sensor LH
16. Fog lamp finisher LH
17.
Bumper side grommet LH
18. Energy absorber
19. Bumper reinforcement
20.
Bumper side bracket LH
21. Grommet
JMKIA2138ZZ
: Clip
: Pawl
JMKIA2139ZZ
JMKIA2140ZZ
EXT-14
< ON-VEHICLE REPAIR >
FRONT BUMPER
6.
Remove bolts (A) of fixing engine lower cover and front fender
protector.
7.
Remove bumper fascia assembly fixing screws (A) (LH/RH) with
screwdriver (B).
8.
Pull the bumper fascia side toward the vehicle side to disengage the fitting of bumper side bracket and
bumper fascia side.
9.
Remove front camera harness clips (A), and then disconnect
front camera harness connector (B). (with FRONT CAMERA).
10. Remove bumper fascia assembly.
CAUTION:
When removing bumper fascia, 2 workers are required so as to prevent it from dropping.
11. Remove the following parts after removing bumper fascia.
• Hood seal assembly (front). Refer to
EXT-20, "Removal and Installation"
.
• Front grille. Refer to
EXT-20, "Removal and Installation"
• Sonar sensor (LH/RH). Refer to
SN-43, "FRONT : Removal and Installation"
.
• License plate bracket
• Front bumper side bracket (LH/RH)
• Front bumper finisher (LH/RH)
• Fog lamp finisher (LH/RH)
12. Remove bumper energy absorber.
13. Remove bumper reinforcement mounting nuts and bolts, and then remove bumper reinforcement with
power tool.
INSTALLATION
Install in the reverse order of removal.
NOTE:
JMKIA2142ZZ
JMKIA2141ZZ
JMKIA2156ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст