Infiniti EX35. Manual — part 841
DOOR OUTSIDE MOLDING
EXT-43
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
4.
Twist and pull up to upper side, and then remove rear door out-
side molding (1).
INSTALLATION
Install in the reverse order of removal.
JMKIA2026ZZ
EXT-44
< ON-VEHICLE REPAIR >
DOOR OUTSIDE LOWER MOLDING
DOOR OUTSIDE LOWER MOLDING
Exploded View
INFOID:0000000003671438
Removal and Installation
INFOID:0000000003719175
REMOVAL
FRONT DOOR OUTSIDE LOWER MOLDING
1.
Front door outside lower molding
2.
Rear door outside lower molding
3.
Front door panel
4.
Double-faced adhesive tape (t: 1.2 mm) 5.
Double-faced adhesive tape (t: 2.5 mm)
Refer to
for symbols in the figure.
JMKIA2213ZZ
DOOR OUTSIDE LOWER MOLDING
EXT-45
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
1.
Remove double-faced adhesive tapes with remover tool (A).
2.
Using a remover tool, disengage the clips from the front door
outside lower molding (1) by starting from the rear.
CAUTION:
• Apply a protective tape (B) on the door to protect the
painted surface from damage.
• Disengage the clips slowly and carefully.
• Do not pull the front door outside lower molding.
3.
Remove front door outside lower molding.
REAR DOOR OUTSIDE LOWER MOLDING
1.
Remove double-faced adhesive tapes with remover tool (A).
2.
Using a remover tool, disengage the clips from the rear door out-
side lower molding (1) by starting from the rear.
CAUTION:
• Apply a protective tape (B) on the door to protect the
painted surface from damage.
• Disengage the clips slowly and carefully.
• Do not pull the front door outside lower molding.
3.
Remove rear door outside lower molding.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Replace double-faced adhesive tape on back of molding with a new tape if door outside lower mold-
ing is reused.
• Do not let air between contact surfaces when installing.
• When installing, check visually the door outside lower molding and the clips, then replace then with
new parts if they have been damaged.
• When installing door outside lower molding, check that clips are securely fitted in panel holes on
body, and then press them in.
• To secure contact, do not wash vehicle within 24 hours after installation.
: Clip
JMKIA2214ZZ
: Clip
JMKIA2215ZZ
EXT-46
< ON-VEHICLE REPAIR >
DOOR PARTING SEAL
DOOR PARTING SEAL
Exploded View
INFOID:0000000003134305
Removal and Installation
INFOID:0000000003719174
REMOVAL
FRONT DOOR PARTING SEAL
1.
Fully open front door.
2.
Using a remover tool (A), disengage the clips from the front door
parting seal (1).
CAUTION:
• Disengage the clips slowly and carefully.
• Do not pull the front door parting seal strongly.
1.
Front door panel
2.
Front door parting sea
3.
Rear door parting seal (lower)
4.
Rear door panel
5.
Rear door parting seal (front)
6.
Double-faced adhesive tape
[t: 1.2 mm (0.047 in)]
7.
Center mud guard
Refer to
of symbols in the figure.
JMKIA2210ZZ
: Clip
JMKIA2211ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст