Infiniti EX35. Manual — part 1564
WW-108
< ON-VEHICLE REPAIR >
FRONT WIPER DRIVE ASSEMBLY
FRONT WIPER DRIVE ASSEMBLY
Exploded View
INFOID:0000000003139019
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000003139020
REMOVAL
1.
Remove front wiper arm. Refer to
WW-106, "Removal and Installation"
2.
Remove cowl top cover. Refer to
EXT-23, "Removal and Installation"
.
3.
Remove bolts from the front wiper drive assembly.
1.
Front wiper drive assembly
JPLIA0974ZZ
1.
Front wiper linkage 1
2.
Shaft seal
3.
Front wiper motor
4.
Front wiper frame
5.
Front wiper linkage 2
: Multi
−
purpose grease or an equivalent.
JPLIA0975ZZ
FRONT WIPER DRIVE ASSEMBLY
WW-109
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
4.
Disconnect the front wiper motor connector.
5.
Remove front wiper drive assembly from the vehicle.
INSTALLATION
1.
Install the front wiper drive assembly to the vehicle.
2.
Connect the front wiper motor connector.
3.
Operate the front wiper to move it to the auto stop position.
4.
Install the cowl top cover. Refer to
EXT-23, "Removal and Installation"
5.
Install front wiper arms. Refer to
WW-106, "Removal and Installation"
Disassembly and Assembly
INFOID:0000000003139021
DISASSEMBLY
1.
Remove the front wiper linkage 1 and 2 from the front wiper drive assembly.
CAUTION:
Do not bend the linkage or damage the plastic part of the ball joint when removing the wiper link-
age.
2.
Remove the front wiper motor mounting screws, and then remove the front wiper motor from the front
wiper frame.
ASSEMBLY
1.
Connect the front wiper motor connector.
2.
Operate the front wiper to move it to the auto stop position.
3.
Disconnect the front wiper motor connector.
4.
Install front wiper motor to front wiper frame.
5.
Install the front wiper linkage 2 to the front wiper motor and the front wiper frame.
6.
Install the front wiper linkage 1 to the front wiper frame.
CAUTION:
• Do not drop front wiper motor or cause it to come into contact with other parts.
• Be careful for the grease condition at the front wiper motor and front wiper linkage joint
(retainer). Apply Multi
−
purpose grease or an equivalent if necessary.
WW-110
< ON-VEHICLE REPAIR >
WIPER AND WASHER SWITCH
WIPER AND WASHER SWITCH
Exploded View
INFOID:0000000003464507
REAR WIPER ARM
WW-111
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
REAR WIPER ARM
Exploded View
INFOID:0000000003464509
Removal and Installation
INFOID:0000000003464510
REMOVAL
1.
Operate the rear wiper to the auto stop position.
2.
Remove the rear wiper arm cover.
3.
Remove the rear wiper arm mounting nut.
4.
Raise rear wiper arm, and remove wiper arm from the vehicle.
INSTALLATION
1.
Clean wiper arm mount as shown in the figure to prevent nut
from being loosened.
2.
Operate the rear wiper motor to the auto stop position.
3.
Adjust the rear wiper blade position. Refer to
.
4.
Install the rear wiper arm by tightening the mounting nut.
5.
Inject the washer fluid.
6.
Operate the rear wiper to the auto stop position.
7.
Check that the rear wiper blades stop at the specified position.
8.
Install the rear wiper arm cover.
Adjustment
INFOID:0000000003464511
REAR WIPER BLADE POSITION ADJUSTMENT
Clearance between the end of back door glass and the top of wiper blade center.
1.
Rear wiper blade
2.
Rear wiper motor
3.
Pivot seal
4.
Rear wiper arm
5.
Rear wiper arm cover
Refer to
JPLIA0976GB
SKIA0082J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст