Infiniti EX35. Manual — part 678
EC-454
< COMPONENT DIAGNOSIS >
[VQ35HR]
FUEL PUMP
Check the following.
• Harness connectors E104, B4
• IPDM E/R harness connector E5
• Harness for open or short between IPDM E/R and “fuel level sensor unit and fuel pump (main)”
>> Repair open circuit or short to power in harness or connectors.
8.
CHECK FUEL PUMP GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect dropping resistor harness connector.
3.
Check the continuity between “fuel level sensor unit and fuel pump (main)” harness connector and
ground.
4.
Also check harness for short to power.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair open circuit or short to power in harness or connectors.
9.
CHECK FUEL PUMP
EC-454, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Replace fuel pump.
10.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace harness or connectors.
Component Inspection
INFOID:0000000003133640
1.
CHECK FUEL PUMP
1.
Turn ignition switch OFF.
2.
Disconnect “fuel level sensor unit and fuel pump (main)” harness connector.
3.
Check resistance between “fuel level sensor unit and fuel pump” terminals as follows.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace “fuel level sensor unit and fuel pump”
Fuel level sensor unit and fuel pump
(main)
Ground
Continuity
Connector
Terminal
B22
3
Ground
Existed
Terminals
Resistance
1 and 3
0.2 - 5.0
Ω
[at 25
°
C (77
°
F)]
ICC BRAKE SWITCH
EC-455
< COMPONENT DIAGNOSIS >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
ICC BRAKE SWITCH
Description
INFOID:0000000003133641
When the brake pedal is depressed, ICC brake switch is turned OFF and stop lamp switch is turned ON. ECM
detects the state of the brake pedal by this input of two kinds (ON/OFF signal).
Refer to
for the ICC function.
Component Function Check
INFOID:0000000003133642
1.
CHECK ICC BRAKE SWITCH FUNCTION
With CONSULT-III
1.
Turn ignition switch ON.
2.
Select “BRAKE SW1” in “DATA MONITOR” mode with CONSULT-III.
3.
Check “BRAKE SW1” indication under the following conditions.
Without CONSULT-III
1.
Turn ignition switch ON.
2.
Check the voltage between ECM harness connector terminals as follows.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000003133643
1.
CHECK ICC BRAKE SWITCH POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect ICC brake switch harness connector.
3.
Turn ignition switch ON.
4.
Check the voltage between ICC brake switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
DETECT MALFUNCTIONING PART
Check the following.
• Fuse block (J/B) connector E103
• 10A fuse (No. 3)
• Harness for open or short between ICC brake switch and fuse
Monitor item
Condition
Indication
BRAKE SW1
Brake pedal
Slightly depressed
OFF
Fully released
ON
ECM
Condition
Voltage (V)
Connector
+
–
Terminal
Terminal
M107
126
(ICC brake switch signal)
128
Brake pedal
Slightly depressed
Approx. 0
Fully released
Battery voltage
ICC brake switch
Ground
Voltage
Connector
Terminal
E114
1
Ground
Battery voltage
EC-456
< COMPONENT DIAGNOSIS >
[VQ35HR]
ICC BRAKE SWITCH
>> Repair open circuit or short to ground in harness or connectors.
3.
CHECK ICC BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT-II
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between ICC brake switch harness connector and ECM harness connector.
4.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E106, M6
• Harness for open or short between ICC brake switch and ECM
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK ICC BRAKE SWITCH
EC-456, "Component Inspection (ICC Brake Switch)"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace ICC brake switch.
6.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
>> INSPECTION END
Component Inspection (ICC Brake Switch)
INFOID:0000000003133644
1.
CHECK ICC BRAKE SWITCH-I
1.
Turn ignition switch OFF.
2.
Disconnect ICC brake switch harness connector.
3.
Check the continuity between ICC brake switch terminals under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK ICC BRAKE SWITCH-II
1.
Adjust ICC brake switch installation. Refer to
BR-7, "Inspection and Adjustment"
2.
Check the continuity between ICC brake switch terminals under the following conditions.
ICC brake switch
ECM
Continuity
Connector
Terminal
Connector
Terminal
E114
2
M107
126
Existed
Terminals
Condition
Continuity
1 and 2
Brake pedal
Fully released
Existed
Slightly depressed
Not existed
Terminals
Condition
Continuity
1 and 2
Brake pedal
Fully released
Existed
Slightly depressed
Not existed
ICC BRAKE SWITCH
EC-457
< COMPONENT DIAGNOSIS >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace ICC brake switch.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст