Infiniti EX35. Manual — part 289
BCS
INSPECTION AND ADJUSTMENT
BCS-3
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
BASIC INSPECTION
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM)
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Description
INFOID:0000000003534203
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle specification with CONSULT-III configuration before
replacement.
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after
replacing BCM.
AFTER REPLACEMENT
CAUTION:
• When replacing BCM, you must perform “WRITE CONFIGURATION” with CONSULT-III.
- Complete the procedure of “WRITE CONFIGURATION” in order.
- If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
- Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• When replacing BCM, perform the system initialization (NATS).
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Special Repair
Requirement
INFOID:0000000003534204
1.
SAVING VEHICLE SPECIFICATION
CONSULT-III Configuration
Perform “READ CONFIGURATION” to save or print current vehicle specification. Refer to
.
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after
replacing BCM.
>> GO TO 2.
2.
REPLACE BCM
.
>> GO TO 3.
3.
WRITING VEHICLE SPECIFICATION
CONSULT-III Configuration
Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Manual selection” to write
vehicle specification. Refer to
BCS-4, "CONFIGURATION (BCM) : Special Repair Requirement"
>> GO TO 4.
4.
INITIALIZE BCM (NATS)
Perform BCM initialization. (NATS)
>> WORK END
CONFIGURATION (BCM)
CONFIGURATION (BCM) : Description
INFOID:0000000003534205
Vehicle specification needs to be written with CONSULT-III because it is not written after replacing BCM.
BCS-4
< BASIC INSPECTION >
INSPECTION AND ADJUSTMENT
Configuration has three functions as follows
NOTE:
Manual setting item: Items which need selection by vehicle specifications
Automatic setting item: Items which are written in automatically (Setting can not be changed)
CAUTION:
• When replacing BCM, you must perform “WRITE CONFIGURATION” with CONSULT-III.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• Never perform “WRITE CONFIGURATION” except for new BCM.
CONFIGURATION (BCM) : Special Repair Requirement
INFOID:0000000003534206
1.
WRITING MODE SELECTION
CONSULT-III Configuration
Select “CONFIGURATION” of BCM.
When writing saved data>>GO TO 2.
When writing manually>>GO TO 3.
2.
PERFORM “WRITE CONFIGURATION - CONFIG FILE”
CONSULT-III Configuration
Perform “WRITE CONFIGURATION - Config file”.
>> WORK END
3.
PERFORM “WRITE CONFIGURATION - MANUAL SELECTION”
CONSULT-III Configuration
1.
Select “WRITE CONFIGURATION - Manual selection”.
2.
Identify the correct model and configuration list. Refer to
BCS-5, "CONFIGURATION (BCM) : Configura-
.
3.
Confirm and/or change setting value for each item.
4.
Select “Setting change”.
CAUTION:
Make sure to select “Setting change” even if the indicated configuration of brand new BCM is
same as the desirable configuration. If not, configuration which is set automatically by selecting
vehicle model can not be memorized.
5.
When “COMMAND FINISHED”, select “END”.
>> GO TO 4.
4.
OPERATION CHECK
Confirm that each function controlled by BCM operates normally.
>> WORK END
Function
Description
READ CONFIGURATION
• Reads the vehicle configuration of current BCM.
• Saves the read vehicle configuration.
WRITE CONFIGURATION - Manual selection
Writes the vehicle configuration with manual selection.
WRITE CONFIGURATION - Config file
Writes the vehicle configuration with saved data.
BCS
INSPECTION AND ADJUSTMENT
BCS-5
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
CONFIGURATION (BCM) : Configuration list
INFOID:0000000003534207
⇔
: Items which confirm vehicle specifications
MANUAL SETTING ITEM
NOTE
Items
Setting value
AUTO LIGHT
WITH
⇔
WITHOUT
—
DTRL
WITH
⇔
WITHOUT
• WITH: With daytime running light system
• WITHOUT: Without daytime running light system
AUTO SETTING ITEM
NOTE
Items
Setting value
H/L BULB
DEFAULT
—
FR FOG LAMP
WITH
—
RR FOG LAMP
WITH
Even on a vehicle without rear fog lamp. It displays “WITH”.
TRANSMISSION
AT with ABS
—
TPMS WITH
—
TIRE PRESSURE
230kPa
—
TR OPEN SW (INT)
MODE1
—
FOG LAMP BULB
SINGLE BULB
—
DI LMP VARIAT
MODE2
—
LIGHT RECOG
MODE4
—
RR WIPER GND
MODE1
—
FR FOG LOGIC
MODE1
—
THEFT ALM AREA
MODE2
—
PANIC ALM TYPE
MODE1
—
RAP FUNC SET
MODE1
—
HAZARD SW TYPE
MODE2
—
BCM AC CONTROL
MODE1
—
H/L WASHER
MODE1
—
Trunk/Glass Hatch select
Glass Hatch
Even on a vehicle without glass hatch. It displays “Glass
Hatch”.
WELCOME LIGHT TIMER
MODE2
—
RAIN SENSOR
WITHOUT
—
REAR WIPER
WITH
—
Key Fob Type
MODE9
—
TRUNK ACT OUTPUT
MODE1
—
FOG ON WITH AUTO LIGHT
WITHOUT
—
AUTO LOCK&UNLOCK FUNC
WITH
—
DROP WIP FUNCTION
WITHOUT
—
HANDLE
LHD
—
WELCOME LIGHT OP SET
WITH
—
WELCOME LIGHT TIMER2
MODE4
—
BCS-6
< FUNCTION DIAGNOSIS >
BODY CONTROL SYSTEM
FUNCTION DIAGNOSIS
BODY CONTROL SYSTEM
System Description
INFOID:0000000003137904
OUTLINE
• BCM (Body Control Module) controls the various electrical components. It inputs the information required to
the control from CAN communication and the signal received from each switch and sensor.
• BCM has combination switch reading function for reading the operation status of combination switches (light,
turn signal, wiper and washer) in addition to a function for controlling the operation of various electrical com-
ponents. It also has the signal transmission function as the passed point of signal and the power saving con-
trol function that reduces the power consumption with the ignition switch OFF.
• BCM is equipped with the diagnosis function that performs the diagnosis with CONSULT-III and various set-
tings.
BCM CONTROL FUNCTION LIST
System
Reference
Combination switch reading system
Signal buffer system
Power consumption control system
Auto light system
•
(Xenon type headlamp)
•
(Halogen type headlamp)
Turn signal and hazard warning lamp system
•
(Xenon type headlamp)
•
(Halogen type headlamp)
Headlamp system
•
(Xenon type headlamp)
•
(Halogen type headlamp)
Parking, license plate and tail lamps system
•
(Xenon type headlamp)
•
(Halogen type headlamp)
Front fog lamp system
•
(Xenon type headlamp)
•
(Halogen type headlamp)
Exterior lamp battery saver system
•
(Xenon type headlamp)
•
(Halogen type headlamp)
Daytime running light system
•
(Xenon type headlamp)
•
(Halogen type headlamp)
Interior room lamp control system
Step lamp system
Interior room lamp battery saver system
Front wiper and washer system
Rear wiper and washer system
Warning chime system
WCS-5, "WARNING CHIME SYSTEM : System Diagram"
Door lock system
Infiniti Vehicle Immobilizer System (IVIS) - NATS
Vehicle security system
Panic alarm
Automatic drive positioner system
ADP-13, "AUTOMATIC DRIVE POSITIONER SYSTEM :
System Diagram"
Rear window defogger system
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст