Infiniti EX35. Manual — part 549
DLN-146
< ON-VEHICLE REPAIR >
[REAR FINAL DRIVE: R200]
FRONT OIL SEAL
6.
Install attachment (A) [SST: KV40104100 (
—
)] to side
flange, and then pull out the side flange with the sliding hammer
(B) [SST: ST36230000 (J-25840-A)].
NOTE:
Circular clip installation position: Final drive side
7.
Remove rear propeller shaft. Refer to
.
8.
Measure the total preload with the preload gauge (A) [SST:
ST3127S000 (J-25765-A)].
NOTE:
Record the preload measurement.
9.
Put matching mark (B) on the end of the drive pinion. The
matching mark (B) should be in line with the matching mark (A)
on companion flange (1).
CAUTION:
For matching mark, use paint. Never damage companion
flange and drive pinion.
NOTE:
The matching mark (A) on the final drive companion flange (1)
indicates the maximum vertical runout position.
10. Remove drive pinion lock nut using the flange wrench.
11. Remove companion flange using pullers.
JSDIA0105ZZ
JSDIA0015ZZ
JSDIA0016ZZ
JSDIA0021ZZ
JSDIA0022ZZ
FRONT OIL SEAL
DLN-147
< ON-VEHICLE REPAIR >
[REAR FINAL DRIVE: R200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
12. Remove front oil seal using the puller (A) [SST: KV381054S0 (J-
34286)].
INSTALLATION
1.
Apply multi-purpose grease to front oil seal lips.
2.
Install front oil seal using the drift (A) [SST: ST30720000 (J-
25405)] as shown in figure.
CAUTION:
• Never reuse oil seal.
• Never incline oil seal when installing.
3.
Align the matching mark (B) of drive pinion with the matching
mark (A) of companion flange (1), and then install the compan-
ion flange (1).
PDIA0980E
PDIA0752J
JSDIA0016ZZ
DLN-148
< ON-VEHICLE REPAIR >
[REAR FINAL DRIVE: R200]
FRONT OIL SEAL
4.
Apply anti-corrosion oil to the thread and seat of new drive pin-
ion lock nut, and temporarily tighten drive pinion lock nut to drive
pinion.
CAUTION:
Never reuse drive pinion lock nut.
5.
Tighten drive pinion lock nut within the limits of specified torque
so as to keep the pinion bearing preload within a standard val-
ues.
CAUTION:
• Adjust to the lower limit of the drive pinion lock nut tight-
ening torque first.
• If the preload torque exceeds the specified value, replace
collapsible spacer and tighten it again to adjust. Never
loosen drive pinion lock nut to adjust the preload torque.
6.
Set a dial indicator (A) vertically to the tip of the drive pinion.
7.
Rotate drive pinion to check for runout.
• If the runout value is still outside of the limit after the phase
has been changed, possible causes are an assembly malfunc-
tion of drive pinion and pinion bearing and malfunction of pin-
ion bearing. Check for these items and repair if necessary.
8.
Make a stamping for identification of front oil seal replacement
frequency. Refer to “Identification stamp of replacement frequency of front oil seal”.
CAUTION:
Make a stamping after replacing front oil seal.
9.
Install rear propeller shaft. Refer to
.
10. Install side flange with the following procedure.
a.
Attach the protector [SST: KV38107900 (J-39352)] to side oil
seal.
b.
After the side flange is inserted and the serrated part of side
gear has engaged the serrated part of flange, remove the pro-
tector.
c.
Put a suitable drift on the center of side flange, then drive it until
sound changes.
NOTE:
When installation is completed, driving sound of the side flange
turns into a sound that seems to affect the whole final drive.
A
: Preload gauge [SST: ST3127S000 (J-25765-A)]
Standard
Total preload torque
: A value that add 0.1 – 0.4
N·m (0.01 – 0.04 kg-m) to
the measured value when
removing.
JSDIA0023ZZ
Limit
Drive pinion runout
: Refer to
JSDIA0043ZZ
SDIA0822E
FRONT OIL SEAL
DLN-149
< ON-VEHICLE REPAIR >
[REAR FINAL DRIVE: R200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
d.
Confirm that the dimension of the side flange (1) installation
measurement (A) in the figure comes into the following.
11. Install drive shaft. Refer to
12. Install rear wheel sensor. Refer to
.
13. Install center muffler. Refer to
.
14. Refill gear oil to the final drive and check oil level. Refer to
15. Check the final drive for oil leakage. Refer to
.
AWD
AWD : Exploded View
INFOID:0000000003135821
Standard
A
: 326 – 328 mm (12.83 – 12.91 in)
JSDIA0106ZZ
1.
Drive pinion lock nut
2.
Companion flange
3.
Front oil seal
4.
Pinion front bearing
5.
Gear carrier
6.
Side oil seal
7.
Side flange
8.
Collapsible spacer
9.
Pinion rear bearing
10. Pinion height adjusting washer
11.
Drive pinion
12. Side bearing adjusting washer
13. Side bearing
14. Side gear thrust washer
15. Circular clip
16. Side gear
17. Lock pin
18. Pinion mate gear
19. Pinion mate thrust washer
20. Pinion mate shaft
21. Drive gear
22. Differential case
23. Bearing cap
24. Filler plug
JSDIA0027GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст