Infiniti EX35. Manual — part 1340
DRIVER AIR BAG MODULE
SR-5
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
4.
Disconnect driver air bag harness connector.
NOTE:
• For installing/removing driver air bag harness connector, insert
thin screwdriver wrapped in tape into notch, lift lock and
remove connector.
• Install connector with lock raised, and push lock into connec-
tor.
• After installing the connector, check that the lock is pushed
securely into it.
5.
Remove the driver air bag module.
CAUTION:
• Always place driver air bag module with pad side facing
upward.
• Do not insert any foreign objects (screwdriver, etc.) into driver
air bag module.
• Do not disassemble driver air bag module.
• Do not expose the driver air bag module to temperatures
exceeding 90
°
C (194
°
F).
• Do not allow oil, grease or water to come in contact with the
driver air bag module.
• Replace the driver air bag module if it has been dropped or
sustained an impact.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Do not use old TORX bolts after removal; replace with new bolts.
• Fix the driver air bag module harness to the harness fixing
hook (A).
• Tighten the TORX bolts after completely adjusting the centers
of fixing holes on the driver air bag module side and the steer-
ing wheel side. If the holes are misaligned, the bolt threads
are damaged and the module is not installed securely.
• In the case that a malfunction is detected by the air bag warning lamp, after reparation or replace-
ment of the malfunctioning parts, reset the memory by self-diagnosis or by the CONSULT-III.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Refer to
SRC-14, "Diagnosis Description"
PHIA0953J
: Upward
JMHIA0539ZZ
JMHIA0009ZZ
JMHIA0540ZZ
SR-6
< ON-VEHICLE REPAIR >
SPIRAL CABLE
SPIRAL CABLE
Exploded View
INFOID:0000000003131584
Removal and Installation
INFOID:0000000003131585
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes.
• Do not use air tools or electric tools for servicing.
REMOVAL
1.
Remove the driver air bag module. Refer to
SR-4, "Removal and Installation"
2.
Disconnect steering horn switch harness connector (A).
3.
Remove the steering wheel. Refer to
ST-16, "Removal and Installation"
4.
Remove the steering column cover (upper/lower). Refer to
IP-12, "Removal and Installation"
.
5.
Remove the spiral cable fixing screws.
1.
Steering column cover upper
2.
Steering column assembly
3.
Steering column cover lower
4.
Driver air bag harness connector
5.
Spiral cable
JMHIA0541ZZ
JMHIA0011ZZ
SPIRAL CABLE
SR-7
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
6.
Disconnect spiral cable body side harness connectors (A).
7.
Pull out forward the spiral cable.
CAUTION:
• Do not disassemble the spiral cable.
• Do not apply lubricant to the spiral cable.
• Do not allow oil, grease, detergent or water to come in contact with the spiral cable.
• Do not impact the spiral cable by dropping, etc. Replace the
spiral cable if it has been dropped or sustained an impact.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• The spiral cable may snap during steering operation if the
cable is installed in an improper position.
The neutral position is set as follows.
• Turn carefully the spiral cable clockwise to the end position.
Then turn it counterclockwise (about 2 and a half turns) and
stop turning at the point (B) on which the stopper insertion
holes are in the same position.
• The service part is installed in the neutral position by the
stopper and can be set without adjusting after the stopper is
removed.
• Do not over turn the spiral cable or go beyond number of
turns required. (These will cause the cable to snap.)
• Adjust the spiral cable locating pin (A) to the steering wheel
locating pin hole (C).
• In the case that a malfunction is detected by the air bag warning lamp, after reparation or replace-
ment of the malfunctioning parts, reset the memory by self-diagnosis or by the CONSULT-III.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Refer to
SRC-14, "Diagnosis Description"
JMHIA0542ZZ
JMHIA0009ZZ
JMHIA0013ZZ
SR-8
< ON-VEHICLE REPAIR >
FRONT PASSENGER AIR BAG MODULE
FRONT PASSENGER AIR BAG MODULE
Exploded View
INFOID:0000000003131586
Removal and Installation
INFOID:0000000003131587
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes.
• Always work from the side of air bag module. Do not work in front of it.
• Do not use air tools or electric tools for servicing.
REMOVAL
1.
Remove the instrument panel assembly. Refer to
IP-12, "Removal and Installation"
.
2.
Remove the front passenger air bag module fixing screws (A).
3.
Disconnect pawls, and then remove front passenger air bag
module (2) from instrument panel assembly (1).
CAUTION:
1.
Instrument panel assembly
2.
Front passenger air bag module
Refer to
for symbols in the figure
JMHIA0543GB
JMHIA0545ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст