Infiniti EX35. Manual — part 1461
TM-232
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
TRANSMISSION ASSEMBLY
24. Install revolution sensor to transmission case. Tighten revolution
sensor bolt to the specified torque.
CAUTION:
• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.
• Do not place in an area affected by magnetism.
25. As shown in the figure, use the drift to drive rear oil seal into the
rear extension (2WD) or adapter case (AWD) until it is flush.
CAUTION:
• Do not reuse rear oil seal.
• Apply ATF to rear oil seal.
26. Install return spring (1) to parking pawl (2).
27. Install parking pawl (with return spring) and pawl shaft to rear
extension (2WD) or adapter case (AWD).
SCIA2320E
SCIA5477E
SCIA6180J
SCIA3424E
TRANSMISSION ASSEMBLY
TM-233
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
28. Install parking actuator support from rear extension (2WD) or
adapter case (AWD).
29. Install needle bearing (1) to rear extension (2WD) or adapter
case (AWD).
CAUTION:
Check the direction of needle bearing. Refer to
"Location of Adjusting Shims, Needle Bearings, Thrust
Washers and Snap Rings"
.
30. Install rear extension assembly (2WD) or adapter case assembly (AWD) according to the following proce-
dures.
a.
2WD
i.
Install seal rings (1) to output shaft.
ii.
Install parking gear (1) to output shaft (2).
SCIA3423E
SCIA6179J
JPDIA0030ZZ
JPDIA0029ZZ
TM-234
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
TRANSMISSION ASSEMBLY
iii.
Install output shaft in transmission case.
CAUTION:
Be careful not to mistake front for rear because both sides
looks similar. (Thinner end is front side.)
iv.
Install bearing race to output shaft.
v.
Apply recommended sealant (Genuine Anaerobic Liquid Gasket
or equivalent. Refer to
GI-15, "Recommended Chemical Prod-
.) to rear extension assembly as shown in the
figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc.
from the transmission case and rear extension assembly
mounting surfaces.
vi. Install rear extension assembly to transmission case.
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
SCIA5030E
SCIA5245E
A
: Start and finish point shall be in
the center of two bolts.
B
: 3 – 5 mm (0.12 – 0.20 in)
Sealant
width (C)
: 1.0 – 2.0 mm (0.04 – 0.08 in)
Sealant
height (C)
: 0.4 – 1.0 mm (0.016 – 0.04 in)
JPDIA0036ZZ
SCIA5029E
TRANSMISSION ASSEMBLY
TM-235
< DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
vii. Tighten rear extension assembly bolts to the specified torque.
b.
AWD
i.
Install seal rings (1) to output shaft.
ii.
Install parking gear (1) to output shaft (2).
iii.
Install output shaft in transmission case.
CAUTION:
Be careful not to mistake front for rear because both sides
looks similar. (Thinner end is front side.)
1
: Self-sealing bolt
A
: Bolt
JPDIA0026ZZ
JPDIA0030ZZ
JPDIA0029ZZ
SCIA5030E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст