Infiniti EX35. Manual — part 1218
RAX-12
< ON-VEHICLE REPAIR >
REAR DRIVE SHAFT
Use paint or similar substance for matching marks. Never scratch the surface.
5.
Remove stopper ring with suitable tool, and pull out housing.
6.
Put matching marks on ball cage/steel ball/inner race assembly
and shaft.
CAUTION:
Use paint or similar substance for matching marks. Never
scratch the surface.
7.
Remove snap ring, then remove ball cage/steel ball/inner race
assembly from shaft.
8.
Remove boot from shaft.
ASSEMBLY
1.
Remove old grease on housing with paper waste.
2.
If plug (1) has been removed, use a drift to press in a new one.
3.
Wrap serration shaft with tape (A) to protect the boot from dam-
age. Install boot and boot bands to shaft.
CAUTION:
Never reuse boot and boot band.
4.
Remove the tape wrapped around the serrated on shaft.
SRA249A
SFA514A
: Press
A
: Drift [SST: KV38100500 (
−
)]
B
: Drift [SST: KV38102200 (
−
)]
JPDIF0016ZZ
JPDIF0009ZZ
REAR DRIVE SHAFT
RAX-13
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
5.
Install ball cage/steel ball/inner race assembly (1), align it with
the matching marks on shaft (2) put during the removal.
6.
Secure ball cage/steel ball/inner race assembly onto shaft with
snap ring (3).
CAUTION:
Never reuse snap ring.
7.
Apply the appropriate amount of grease onto housing and slid-
ing surface.
8.
Install stopper ring to housing.
CAUTION:
Never reuse stopper ring.
9.
After installed, pull shaft to check engagement between housing and stopper ring.
10. Install boot securely into grooves (indicated by “*” marks) shown
in the figure.
CAUTION:
If grease adheres to the boot mounting surfaces (indicated
by “*” marks) on shaft or housing, boot may be removed.
Remove all grease from the surfaces.
11. To prevent from deformation of the boot, adjust the boot installa-
tion length (L) to the value shown below by inserting the suitable
tool into the inside of boot from the large diameter side of boot
and discharging inside air.
CAUTION:
• If the boot installation length is outside the standard, it may cause breakage in boot.
• Be careful not to touch the inside of the boot with the tip of tool.
12. Install boot bands securely as shown in the figure.
CAUTION:
Never reuse boot band.
13. Secure housing and shaft, and then make sure that they are in
the correct position when rotating boot. Install them with boot
band when the mounting positions become incorrect.
CAUTION:
Never reuse boot band.
Inspection
INFOID:0000000003138887
INSPECTION AFTER REMOVAL
• Move joint up/down, left/right, and in the axial direction. Check for any rough movement or significant loose-
ness.
Standard
Grease amount
: Refer to
.
Standard
L
: Refer to
.
JPDIG0004ZZ
JPDIF0019ZZ
PDIA1188J
RAX-14
< ON-VEHICLE REPAIR >
REAR DRIVE SHAFT
• Check boot for cracks or other damage, and also for grease leak-
age.
• If a malfunction is found, disassemble drive shaft, and then replace
with new one.
RAA0030D
SERVICE DATA AND SPECIFICATIONS (SDS)
RAX-15
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000003138888
Drive Shaft
INFOID:0000000003138889
Item
Standard
Axial end play
0.05 mm (0.002 in) or less
Joint
Wheel side
Final drive side
Grease quantity
100 – 130 g (3.53 – 4.58 oz)
105 – 125 g (3.70 – 4.40 oz)
Boots installed length
133.5 mm (5.26 in)
130.2 mm (5.13 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст