Infiniti G35 (V35) Sedan. Manual — part 26
ADP-98
< COMPONENT DIAGNOSIS >
FRONT DOOR SWITCH (DRIVER SIDE)
NO
>> Repair or replace harness.
3.
CHECK FRONT DOOR SWITCH (DRIVER SIDE)
ADP-98, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace front door switch (driver side).
4.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace BCM.
NO
>> Repair or replace the malfunctioning part.
Component Inspection
INFOID:0000000000960704
1.
CHECK FRONT DOOR SWITCH (DRIVER SIDE)
1.
Turn ignition switch OFF.
2.
Disconnect front door switch (driver side) connector.
3.
Check continuity between front door switch (driver side) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front door switch (driver side).
Terminal
Condition
Continuity
Front door switch (driver side)
2
Ground part of door
switch
Front door switch
(driver side)
Pushed
Not existed
Released
Existed
SLIDING SENSOR
ADP-99
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
SLIDING SENSOR
Description
INFOID:0000000000960705
• The sliding sensor is installed to the seat slide cushion frame.
• The pulse signal is inputted to the driver seat control unit when sliding is performed.
• The driver seat control unit counts the pulse and calculates the sliding amount of the seat.
Component Function Check
INFOID:0000000000960706
1.
CHECK FUNCTION
1.
Select “SLIDE PULSE” in “Data monitor” mode with CONSULT-III.
2.
Check sliding sensor signal under the following conditions.
*1
: The value at the seat position attained when the battery is connected is considered to be 32768.
Is the indication normal?
YES
>> INSPECTION END
NO
>> Perform daiagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000000960707
1.
CHECK SLIDING SENSOR SIGNAL
1.
Turn ignition switch ON.
2.
Read voltage signal between driver seat control unit harness connector and ground with osiloscope.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 2.
2.
CHECK SLIDING SENSOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect driver seat control unit and sliding sensor connector.
3.
Check continuity between driver seat control unit harness connector and sliding sensor harness connec-
tor.
Monitor item
Condition
Valve
SLIDE PULSE
Seat sliding
Operate (forward)
Change (increase)
*1
Operate (backward)
Change (decrease)
Release
No change
*1
Terminals
Condition
Voltage signal
(+)
(–)
Sliding sensor connector
Terminal
B453
24
Ground
Seat sliding
Operate
Other than
above
0 or 5
JMJIA0119ZZ
Driver seat control unit
connector
Terminal
Sliding sensor
connector
Terminal
Continuity
B451
24
B453
24
Existed
ADP-100
< COMPONENT DIAGNOSIS >
SLIDING SENSOR
4.
Check continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK SLIDING SENSOR POWER SUPPLY
1.
Connect driver seat control unit connector.
2.
Turn ignition switch ON.
3.
Check sliding sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK SLIDING SENSOR POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect driver seat control unit connector.
3.
Check continuity between driver seat control unit harness connector and sliding sensor harness connec-
tor.
4.
Check continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
5.
CHECK SLIDING SENSOR GROUND
1.
Turn ignition switch OFF.
2.
Disconnect driver seat control unit connector.
3.
Check continuity between driver seat control unit harness connector and sliding sensor harness connec-
tor.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK SEAT OPERATION
1.
Connect driver seat control unit and sliding sensor connector.
Driver seat control unit
connector
Terminal
Ground
Continuity
B451
24
Not existed
Terminals
Voltage (V)
(Approx.)
(+)
(–)
Sliding sensor connector
Terminal
B453
16
Ground
5
Driver seat
control unit connector
Terminal
Sliding sensor
connector
Terminal
Continuity
B451
16
B453
16
Existed
Driver seat control unit
connector
Terminal
Ground
Continuity
B451
16
Not existed
Driver seat control unit
connector
Terminal
Sliding sensor
connector
Terminal
Continuity
B451
31
B453
31
Existed
SLIDING SENSOR
ADP-101
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
2.
Check seat operation (except sliding operation) with memory function.
Is the operation normal?
YES
>> Replace sliding sensor. (Built in seat slide cushion frame.)
NO
>> Replace driver seat control unit.
7.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace driver seat control unit.
NO
>> Repair or replace the malfunctioning part.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст