Infiniti G35 (V35) Sedan. Manual — part 25
ADP-94
< COMPONENT DIAGNOSIS >
DETENTION SWITCH
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace driver seat control unit.
NO
>> Repair or replace the malfunctioning part.
PARKING BRAKE SWITCH
ADP-95
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
PARKING BRAKE SWITCH
Description
INFOID:0000000000960697
Parking brake switch is installed on parking brake lever. It is turned ON when the parking brake is applied. The
driver seat control unit judges that the parking brake is engaged if continuity exists in this circuit.
Component Function Check
INFOID:0000000000960698
1.
CHECK PARKING BRAKE SWITCH INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Select “PARK BRAKE SW” in “Data monitor” mode with CONSULT-III.
3.
Check parking brake switch signal under the following conditions.
Is the indication normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000000960699
1.
CHECK PARKING BRAKE SWITCH SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between driver seat control harness connector unit and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK PARKING BRAKE SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect driver seat control unit and parking brake switch connector.
3.
Check continuity between driver seat control unit harness connector and parking brake switch harness
connector.
4.
Check continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK PARKING BRAKE SWITCH
ADP-96, "Component Inspection"
.
Monitor item
Condition
Status
PARK BRAKE SW
Parking brake
Applied
ON
Release
OFF
Driver seat control unit
connector
Terminal
Condition
Voltage (V)
(Approx.)
(+)
(-)
M51
8
Ground
Parking brake
Applied
0
Release
Battery voltage
Driver seat control unit connec-
tor
Terminal
Parking brake switch
Terminal
Continuity
M51
8
B14
1
Existed
Driver seat control unit connec-
tor
Terminal
Ground
Continuity
M51
8
Not existed
ADP-96
< COMPONENT DIAGNOSIS >
PARKING BRAKE SWITCH
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Adjust or replace parking brake switch.
4.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace driver seat control unit.
NO
>> Repair or replace malfunctioning part.
Component Inspection
INFOID:0000000000960700
1.
CHECK PARKING BRAKE SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect parking brake switch connector.
3.
Check continuity between parking brake switch terminal and ground part of parking brake switch.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Adjust or replace parking brake switch.
Terminal
Condition
Continuity
Parking brake switch
1
Ground part of
parking brake switch
Parking brake
Applied
Existed
Release
Not existed
FRONT DOOR SWITCH (DRIVER SIDE)
ADP-97
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
FRONT DOOR SWITCH (DRIVER SIDE)
Description
INFOID:0000000000960701
Detects front door (driver side) open/close condition.
Component Function Check
INFOID:0000000000960702
1.
CHECK FUNCTION
1.
Select “DOOR SW-DR” in “Data monitor” mode with CONSULT-III.
2.
Check the front door switch (driver side) signal under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
.
Diagnosis Procedure
INFOID:0000000000960703
1.
CHECK FRONT DOOR SWITCH (DRIVER SIDE) SIGNAL
1.
Turn ignition switch OFF.
2.
Check signal between BCM connector and ground with oscilloscope.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK FRONT DOOR SWITCH (DRIVER SIDE) CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM connector and front door switch (driver side) connector.
3.
Check continuity between BCM connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
Monitor item
Condition
Status
DOOR SW-DR
Front door switch
(driver side)
Open
ON
Close
OFF
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(–)
BCM
connector
Terminal
M123
150
Ground
Front door
(driver side)
Open
0
Close
JPMIA0011GB
BCM connector
Terminal
Door switch
connector
Terminal
Continuity
M123
150
B16 (Driver side)
2
Existed
BCM connector
Terminal
Ground
Continuity
M123
150
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст