Infiniti G35 (V35) Sedan. Manual — part 915
CHASSIS MAINTENANCE
MA-25
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
1.
Measure propeller shaft runout at several points by rotating final
drive companion flange with hands.
2.
If runout still exceeds specifications, separate propeller shaft at
final drive companion flange; then rotate companion flange 90,
180, 270 degrees and install propeller shaft.
3.
Check runout again. If runout still exceeds specifications, replace propeller shaft assembly.
4.
Check the vibration by driving vehicle.
RUNOUT MEASURING POINT
• Propeller shaft runout measuring point (Point “ ”).
REAR PROPELLER SHAFT: 3S80A
REAR PROPELLER SHAFT: 3S80A : Inspection
INFOID:0000000000967327
NOISE
• Check the propeller shaft tube surface for dents or cracks. If damaged, replace propeller shaft assembly.
• If center bearing is noisy or damaged, replace propeller shaft assembly.
VIBRATION
• If vibration is present at high speed, inspect propeller shaft runout first.
1.
Measure propeller shaft runout at several points by rotating final
drive companion flange with hands.
2.
If runout still exceeds specifications, separate propeller shaft at
final drive companion flange; then rotate companion flange 90,
180, 270 degrees and install propeller shaft.
3.
Check runout again. If runout still exceeds specifications,
replace propeller shaft assembly.
4.
Check the vibration by driving vehicle.
RUNOUT MEASURING POINT
: Vehicle front
Limit
Propeller shaft runout
: Refer to
.
PDIA0767J
Dimension
A: 381.5 mm (15.02 in)
PDIA0768J
Limit
Propeller shaft runout
: Refer to
.
SDIA1087E
MA-26
< ON-VEHICLE MAINTENANCE >
CHASSIS MAINTENANCE
• Propeller shaft runout measuring point (Point “ ”).
REAR PROPELLER SHAFT: 3S80A-R
REAR PROPELLER SHAFT: 3S80A-R : Inspection
INFOID:0000000000967328
NOISE
• Check the propeller shaft tube surface for dents or cracks. If damaged, replace propeller shaft assembly.
• If center bearing is noisy or damaged, replace propeller shaft assembly.
VIBRATION
• If vibration is present at high speed, inspect propeller shaft runout first.
1.
Measure propeller shaft runout at several points by rotating final
drive companion flange with hands.
2.
If runout still exceeds specifications, separate propeller shaft at
final drive companion flange; then rotate companion flange 120,
240 degrees and install propeller shaft.
3.
Check runout again. If runout still exceeds specifications,
replace propeller shaft assembly.
4.
Check the vibration by driving vehicle.
RUNOUT MEASURING POINT
• Propeller shaft runout measuring point (Point “ ”).
REAR PROPELLER SHAFT: 3S81A-1VL107
REAR PROPELLER SHAFT: 3S81A-1VL107 : Inspection
INFOID:0000000000967329
NOISE
• Check the propeller shaft tube surface for dents or cracks. If damaged, replace propeller shaft assembly.
• If center bearing is noisy or damaged, replace propeller shaft assembly.
VIBRATION
• If vibration is present at high speed, inspect propeller shaft runout first.
: Vehicle front
Dimension
A: 192 mm (7.56 in)
B: 172 mm (6.77 in)
C: 170 mm (6.69 in)
PDIA0770J
Limit
Propeller shaft runout
SDIA1087E
: Vehicle front
Dimension
A: 192 mm (7.56 in)
B: 172 mm (6.77 in)
C: 172 mm (6.77 in)
JSDIA0169ZZ
CHASSIS MAINTENANCE
MA-27
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
1.
Measure propeller shaft runout at several points by rotating final
drive companion flange with hands.
2.
If runout still exceeds specifications, separate propeller shaft at
final drive companion flange; then rotate companion flange 60,
120 180, 240, 300 degrees and install propeller shaft.
3.
Check runout again. If runout still exceeds specifications,
replace propeller shaft assembly.
4.
Check the vibration by driving vehicle.
RUNOUT MEASURING POINT
• Propeller shaft runout measuring point (Point “ ”).
FRONT DIFFERENTIAL GEAR OIL: F160A
FRONT DIFFERENTIAL GEAR OIL: F160A : Inspection
INFOID:0000000000967330
OIL LEAKAGE
Make sure that oil is not leaking from final drive assembly or around it.
OIL LEVEL
• Remove filler plug (1) and check oil level from filler plug mounting
hole as shown in the figure.
CAUTION:
Never start engine while checking oil level.
• Set a gasket on filler plug (1) and install it on final drive assembly.
.
CAUTION:
Never reuse gasket.
FRONT DIFFERENTIAL GEAR OIL: F160A : Draining
INFOID:0000000000967331
1.
Stop engine.
Limit
Propeller shaft runout
: Refer to
.
SDIA1087E
: Vehicle front
Dimension
A: 162 mm (6.38 in)
B: 245 mm (9.65 in)
C: 185 mm (7.28 in)
PDIA0772J
PDIA0782J
MA-28
< ON-VEHICLE MAINTENANCE >
CHASSIS MAINTENANCE
2.
Remove drain plug (1) and drain gear oil.
3.
Set a gasket on drain plug (1) and install it to final drive assem-
bly and tighten to the specified torque. Refer to
CAUTION:
Never reuse gasket.
FRONT DIFFERENTIAL GEAR OIL: F160A : Refilling
INFOID:0000000000967332
1.
Remove filler plug (1). Fill with new gear oil until oil level reaches
the specified level near filler plug mounting hole.
2.
After refilling oil, check oil level. Set a gasket to filler plug (1),
then install it to final drive assembly. Refer to
CAUTION:
Never reuse gasket.
REAR DIFFERENTIAL GEAR OIL: R200
REAR DIFFERENTIAL GEAR OIL: R200 : Inspection
INFOID:0000000000967333
OIL LEAKEGE
• Make sure that oil is not leaking from final drive assembly or around it.
OIL LEVEL
• Remove filler plug (1) and check oil level from filler plug mounting
hole as shown in the figure.
CAUTION:
Never start engine while checking oil level.
• Set a gasket on filler plug (1) and install it on final drive assembly.
Refer to
DLN-174, "2WD : Exploded View"
(2WD models),
(AWD models).
CAUTION:
Never reuse gasket.
REAR DIFFERENTIAL GEAR OIL: R200 : Draining
INFOID:0000000000967334
1.
Stop engine.
PDIA0781J
Oil grade and Viscosity
: Refer to
.
Oil capacity
: Refer to
.
PDIA0782J
PDIA0749J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст