Infiniti G35 (V35) Sedan. Manual — part 386
DOOR
DLK-205
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2.
Remove the mounting bolts of the check link on the vehicle.
3.
Remove the door side hinge mounting nuts and remove the door assembly.
CAUTION:
• When removing and installing the rear door assembly, support the door with a jack and cloth to pro-
tect the door and body.
• When removing and installing rear door assembly, perform the fitting adjustment. Refer to
.
• Check the hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installing, apply touch-up paint (the body color) onto the head of the hinge mounting nuts.
• Operate with two workers, because of its heavy weight.
• Check rear door open/close operation after installation.
INSTALLATION
Install in the reverse order of removal.
REAR DOOR : Adjustment
INFOID:0000000000961276
CLEARANCE, SURFACE HEIGHT AND SURFACE MISMATCH ADJUSTMENT
1.
Check the clearance and surface height and surface mismatch between the rear door and each part visu-
ally and by touching.(Fitting standard dimension in the table below should be satisfied.)
2.
In case out of specification, adjust them according to the procedures shown below.
3.
Remove the center pillar upper garnish and center pillar lower garnish. Refer to
.
4.
Loosen the hinge mounting nuts on door side.
5.
Adjust the surface height and surface mismatch of the rear door according to the fitting standard dimen-
sion.
6.
Temporarily tighten the hinge mounting nuts on door side.
7.
Loosen the hinge mounting nuts and bolts on body side.
8.
Raise the rear door at rear end to adjust clearance of the rear door according to the fitting standard dimen-
sion.
9.
After adjustment tighten bolts and nuts to the specified torque.
10. Install the center pillar upper garnish and center pillar lower garnish. Refer to
.
JMKIA0016ZZ
Parts
Portion
Clearance
Surface height
Surface
mismatch
Front door – rear door
B – B
2.5 – 4.5
(0.098 – 0.177)
−
1.0 – 1.0
(–0.039 – 0.039)
—
Rear door – rear fender
C – C
2.5 – 4.5
(0.098 – 0.177)
−
1.0 – 1.0
(
−
0.039 – 0.039)
—
Front door sash molding –
rear door weather-strip
G
—
−
1.5 – 1.5
(
−
0.059 – 0.059)
—
Front door outside molding –
rear door outside molding
H
—
−
1.5 – 1.5
(
−
0.059 – 0.059)
−
1.5 – 1.5
(
−
0.059 – 0.059)
DLK-206
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
DOOR
STRIKER ADJUSTMENT
Adjust the striker so that it becomes parallel with the lock insertion
direction.
PIIB2804J
DOOR LOCK
DLK-207
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR LOCK
FRONT DOOR LOCK
FRONT DOOR LOCK : Exploded View
INFOID:0000000000961277
FRONT DOOR LOCK : Removal and Installation
INFOID:0000000000961278
REMOVAL
1.
Remove the front door finisher. Refer to
INT-10, "Removal and Installation"
2.
Disconnect the inside handle knob cable and lock knob cable
from the back side of the front door finisher.
1.
Inside handle cap
2.
Inside handle
3.
Door key cylinder assembly (Driver
side)
Outside handle escutcheon (Pas-
senger side)
4.
Outside handle
5.
Rear gasket
6.
Front gasket
7.
Key cylinder rod (Driver side only)
8.
Door lock assembly
9.
Striker
10. Grommet
11.
Lock knob cable
12. Inside handle knob cable
13. Outside handle cable
Refer to
JMKIA0018GB
JMKIA0019ZZ
DLK-208
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
DOOR LOCK
3.
Remove the front door glass and front door module assembly. Refer to
GW-16, "Removal and Installation"
4.
Remove door side grommet, and remove door key cylinder assembly (driver side) and outside handle
escutcheon (passenger side) bolts (TORX T30) from grommet hole.
CAUTION:
Do not forcibly remove the TORX bolts (T30).
5.
Disconnect door antenna and door request switch connector
and remove harness clamp. (Models with Intelligent Key sys-
tem)
6.
Reach in to separate the key cylinder rod connection (on the handle).
7.
Disconnect door key cylinder switch harness connector.
8.
While pulling the outside handle, remove door key cylinder
assembly.
9.
Disconnect front door request switch harness connector (with Intelligent Key system).
10. While pulling outside handle, slide toward rear of vehicle to
remove outside handle.
JMKIA0020ZZ
JMKIA0021ZZ
PIIB5809E
PIIB5810E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст