Infiniti G35 (V35) Sedan. Manual — part 922
CHANGE OVER SWITCH
MIR-15
< COMPONENT DIAGNOSIS >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
Check continuity between door mirror remote control switch connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1.
Connect automatic drive positioner control unit connector.
2.
Turn ignition switch ON.
3.
Check voltage between automatic drive positioner control unit connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace automatic drive positioner control unit. Refer to
ADP-218, "Removal and Installation"
.
5.
CHECK CHANGEOVER SWITCH
Check changeover switch.
Refer to
MIR-15, "Component Inspection"
Is the inspection result normal?
YES
>> Refer to
GI-39, "Intermittent Incident"
.
NO
>> Replace door mirror remote control switch. Refer to
MIR-68, "Removal and Installation"
6.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to
GI-39, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-218, "Removal and Installation"
.
NO
>> Repair or replace the malfunctioning parts.
Component Inspection
INFOID:0000000000962323
1.
CHECK CHANGEOVER SWITCH
Check door mirror remote control switch.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace door mirror remote control switch. Refer to
MIR-68, "Removal and Installation"
Door mirror remote control switch connector
Terminal
Ground
Continuity
D7
7
Existed
Terminals
Voltage (V)
(Approx.)
(+)
(-)
Automatic drive positioner control unit
connector
Terminal
M51
2
Ground
5
18
Terminal
Change over switch condition
Continuity
Door mirror remote control switch
10
7
LEFT
Existed
Other than above
Not existed
11
RIGHT
Existed
Other than above
Not existed
MIR-16
< COMPONENT DIAGNOSIS >
[WITH ADP]
DOOR MIRROR MOTOR
DOOR MIRROR MOTOR
Description
INFOID:0000000000962324
It makes mirror face operate from side to side and up and down with the electric power that AUTOMATIC
DRIVE POSITIONER CONTROL UNIT supplies.
Component Function Check
INFOID:0000000000962325
1.
CHECK DOOR MIRROR MOTOR FUNCTION
Check the operation with “MIRROR MOTOR RH” and “MIRROR MOTOR LH” in “ACTIVE TEST” mode with
CONSULT-III
Refer to
ADP-48, "CONSULT-III Function"
.
Is the inspection result normal?
YES
>> Door mirror motor function is OK.
NO
>> Refer to
Diagnosis Procedure
INFOID:0000000000962326
1.
CHECK DOOR MIRROR MOTOR INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between door mirror connector and ground.
Is the inspection result normal?
YES
>> Refer to
MIR-18, "Component Inspection"
NO
>> GO TO 2.
2.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector and door mirror connector.
3.
Check continuity between automatic drive positioner control unit connector and door mirror connector.
[Door mirror driver side]
[Door mirror passenger side]
Terminals
Door mirror remote control switch
condition
Voltage (V)
(Approx.)
(+)
(–)
Door mirror
connector
Terminal
D3 (Driver side)
D33 (Passenger side)
5
Ground
UP
Battery voltage
Other than above
0
6
LEFT
Battery voltage
Other than above
0
7
DOWN / RIGHT
Battery voltage
Other than above
0
Automatic drive positioner con-
trol unit connector
Terminal
Door mirror (driver side) connec-
tor
Terminal
Continuity
M51
16
D3
7
Existed
31
5
32
6
Automatic drive positioner control
unit connector
Terminal
Door mirror (passenger side)
connector
Terminal
Continuity
M51
14
D33
5
Existed
15
6
30
7
DOOR MIRROR MOTOR
MIR-17
< COMPONENT DIAGNOSIS >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
4.
Check continuity between automatic drive positioner control unit connector and ground.
[Door mirror driver side]
[Door mirror passenger side]
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1.
Connect automatic drive positioner control unit connector.
2.
Turn ignition switch ON.
3.
Check voltage between automatic drive positioner control unit connector and ground.
[Door mirror driver side]
[Door mirror passenger side]
Is the inspection result normal?
YES
>> Refer to
MIR-18, "Component Inspection"
NO
>> Replace automatic drive positioner control unit. Refer to
ADP-218, "Removal and Installation"
.
4.
CHECK DOOR MIRROR MOTOR
Check door mirror motor.
Refer to
MIR-18, "Component Inspection"
Automatic drive positioner control unit connec-
tor
Terminal
Ground
Continuity
M51
16
Not existed
31
32
Automatic drive positioner control unit connec-
tor
Terminal
Ground
Continuity
M51
14
Not existed
15
30
Terminals
Mirror switch condition
Voltage (V)
(Approx.)
(+)
(-)
Automatic drive positioner con-
trol unit connector
Terminal
M51
16
Ground
DOWN / RIGHT
Battery voltage
Other than above
0
31
UP
Battery voltage
Other than above
0
32
LEFT
Battery voltage
Other than above
0
Terminals
Mirror switch condition
Voltage (V)
(Approx.)
(+)
(-)
Automatic drive positioner con-
trol unit connector
Terminal
M51
14
Ground
UP
Battery voltage
Other than above
0
15
LEFT
Battery voltage
Other than above
0
30
DOWN / RIGHT
Battery voltage
Other than above
0
MIR-18
< COMPONENT DIAGNOSIS >
[WITH ADP]
DOOR MIRROR MOTOR
Is the inspection result normal?
YES
>> Refer to
GI-39, "Intermittent Incident"
.
NO
>> Replace door mirror. Refer to
MIR-67, "Removal and Installation"
.
Component Inspection
INFOID:0000000000962327
1.
CHECK DOOR MIRROR MOTOR-I
Check that door mirror motor does not trap foreign objects and does not have any damage.
Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace door mirror.Refer to
MIR-67, "Removal and Installation"
2.
CHECK DOOR MIRROR MOTOR-II
1.
Turn ignition switch OFF.
2.
Disconnect door mirror connector.
3.
Apply 12V to each power supply terminal of door mirror motor.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace door mirror. Refer to
MIR-67, "Removal and Installation"
.
Door mirror connector
Terminal
Operational direction
(+)
(–)
D3 (Driver side)
D33 (Passenger side)
7
6
RIGHT
6
7
LEFT
5
7
UP
7
5
DOWN
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст