Infiniti G35 (V35) Sedan. Manual — part 921

MIRROR SWITCH

MIR-11

< COMPONENT DIAGNOSIS >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

COMPONENT DIAGNOSIS

MIRROR SWITCH

Description

INFOID:0000000000962316

It operates angle of the door mirror face.
It transmits mirror face adjust operation to AUTOMATIC DRIVE POSITIONER CONTROL UNIT.

Component Function Check

INFOID:0000000000962317

1.

CHECK MIRROR SWITCH FUNCTION

Check the operation on “MIR CON SW–UP/DN” and “MIR CON SW–RH/LH” in “DATA MONITOR” mode
with CONSULT-III.
Refer to

ADP-48, "CONSULT-III Function"

.

Is the inspection result normal?

YES

>> Mirror switch function is OK.

NO

>> Refer to

MIR-11, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000000962318

1.

CHECK MIRROR SWITCH FUNCTION

1.

Turn ignition switch ON.

2.

Check voltage between automatic drive positioner control unit connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> GO TO 2.

2.

CHECK HARNESS CONTINUITY

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit and door mirror remote control switch connector.

3.

Check continuity between automatic drive positioner control unit connector and door mirror remote control
switch connector.

4.

Check continuity between automatic drive positioner control unit connector and ground.

Terminals

Mirror switch

Condition

Voltage (V)

(Approx.)

(+)

(–)

Automatic drive positioner control

unit connector

Terminal

M51

3

Ground

UP

0

Other than above

5

4

LEFT

0

Other than above

5

19

DOWN

0

Other than above

5

20

RIGHT

0

Other than above

5

Automatic drive positioner control

unit connector

Terminal

Door mirror remote control

switch connector

Terminal

Continuity

M51

3

D7

15

Existed

4

13

19

12

20

4

MIR-12

< COMPONENT DIAGNOSIS >

[WITH ADP]

MIRROR SWITCH

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT

Check continuity between door mirror remote control switch connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL

1.

Connect automatic drive positioner control unit connector.

2.

Turn ignition switch ON.

3.

Check voltage between automatic drive positioner control unit and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace automatic drive positioner control unit. Refer to

ADP-218, "Removal and Installation"

.

5.

CHECK MIRROR SWITCH

Check mirror switch
Refer to

MIR-12, "Component Inspection"

.

Is the inspection result normal?

YES

>> Refer to

GI-39, "Intermittent Incident"

.

NO

>> Replace door mirror remote control switch. Refer to

MIR-68, "Removal and Installation"

.

6.

CHECK INTERMITTENT INCIDENT

Check intermittent incident.
Refer to

GI-39, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace automatic drive positioner control unit. Refer to

ADP-218, "Removal and Installation"

.

NO

>> Repair or replace the malfunctioning parts.

Component Inspection

INFOID:0000000000962319

1.

CHECK MIRROR SWITCH

Automatic drive positioner control unit

connector

Terminal

Ground

Continuity

M51

3

Not existed

4

19

20

Door mirror remote control switch connector

Terminal

Ground

Continuity

D7

7

Existed

Terminals

Voltage (V)

(Approx.)

(+)

(-)

Automatic drive positioner control unit

connector

Terminal

M51

3

Ground

5

4

19

20

MIRROR SWITCH

MIR-13

< COMPONENT DIAGNOSIS >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

Check door mirror remote control switch.

Is the inspection result normal?

YES

>> INSPECTION END.

NO

>> Replace door mirror remote control switch.Refer to

MIR-68, "Removal and Installation"

.

Terminal

Mirror switch condition

Continuity

Door mirror remote

control switch

4

7

RIGHT

Existed

Other than above

Not existed

13

LEFT

Existed

Other than above

Not existed

15

UP

Existed

Other than above

Not existed

12

DOWN

Existed

Other than above

Not existed

MIR-14

< COMPONENT DIAGNOSIS >

[WITH ADP]

CHANGE OVER SWITCH

CHANGE OVER SWITCH

Description

INFOID:0000000000962320

Changeover switch is integrated into door mirror remote control switch.
Changeover switch has three positions (L, N and R).
It changes door mirror motor operation by transmitting control signal to automatic drive positioner control unit.

Component Function Check

INFOID:0000000000962321

1.

CHECK CHANGEOVER SWITCH FUNCTION

Check the operation on “MIR CHNG SW-R” or “MIR CHNG SW-L” in “DATA MONITOR” mode with CON-
SULT-III.
Refer to

ADP-48, "CONSULT-III Function"

.

Is the inspection result normal?

YES

>> Changeover switch function is OK.

NO

>> Refer to

MIR-14, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000000962322

1.

CHECK CHANGEOVER SWITCH SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage between automatic drive positioner control unit connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> GO TO 2.

2.

CHECK HARNESS CONTINUITY

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit and door mirror remote control switch connector.

3.

Check continuity between automatic drive positioner control unit connector and door mirror remote control
switch connector.

4.

Check continuity between automatic drive positioner control unit connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

Terminals

Change over switch condition

Voltage (V)

(Approx.)

(+)

(-)

Automatic drive positioner

control unit connector

Terminal

M51

2

Ground

RIGHT

0

Other than above

5

18

LEFT

0

Other than above

5

Automatic drive positioner

control unit connector

Terminal

Door mirror remote control switch

connector

Terminal

Continuity

M51

2

D7

11

Existed

18

10

Automatic drive positioner control unit

connector

Terminal

Ground

Continuity

M51

2

Not existed

18