Infiniti G35 (V35) Sedan. Manual — part 822
INT-12
< ON-VEHICLE REPAIR >
DOOR FINISHER
8.
Insert a remover tool (A) into clips on door finisher (1), and dis-
engage clips.
CAUTION:
Insert a remover tool (A) into the part shown by the arrow
(between the clips and the body side panel).
9.
Pull up door finisher and pull out toward vehicle inside.
• Disconnect seat memory switch connector (A). (with ADP)
• Disconnect tweeter connector (B). (with BASE AUDIO)
• Disconnect front door squawker connector (B). (with BOSE
AUDIO)
10. Disconnect lock knob cable (1) and inside handle cable (2) from
door inside handle assembly.
11. Remove door finisher.
12. Remove the following parts after removing door finisher.
• Front door inside handle assembly. Refer to
DLK-207, "FRONT DOOR LOCK : Removal and Installa-
• Rear door inside handle assembly. Refer to
DLK-210, "REAR DOOR LOCK : Removal and Installation"
.
• Seat memory switch. (with ADP) Refer to
ADP-219, "Removal and Installation"
• Tweeter (with BASE AUDIO). Refer to
AV-115, "Removal and Installation"
.
• Front door squawker (with BOSE AUDIO). Refer to
AV-294, "Removal and Installation"
.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When installing door finisher, check that clips are securely fitted in panel holes on body, and then
press them in.
: Clip
JMJIA0078GB
JMJIA0080GB
JMJIA0079GB
BODY SIDE TRIM
INT-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
BODY SIDE TRIM
Exploded View
INFOID:0000000000960436
Removal and Installation
INFOID:0000000000960437
CAUTION:
• Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
• Do not damage the body.
REMOVAL
FRONT PILLAR GARNISH
1.
Release front pillar portion of front body side welt.
1.
Front pillar garnish
2.
Front body side welt
3.
Front kicking plate inner
4.
Front kicking plate outer
5.
Dash side finisher
6.
Center pillar upper garnish
7.
Center pillar lower garnish
8.
Rear body side welt
9.
Rear kicking plate inner
10. Rear kicking plate outer
11. Rear wheel house garnish
12. Rear pillar finisher
Clip
Pawl
Metal clip
JMJIA0067GB
INT-14
< ON-VEHICLE REPAIR >
BODY SIDE TRIM
2.
Remove pillar garnish mounting metal clips with a remover tool
(A), and then remove pillar garnish (1).
DASH SIDE FINISHER
1.
Remove instrument passenger lower cover. (Passenger side only) Refer to
2.
Remove kicking plate inner.
3.
Remove clip (A).
4.
Remove dash side finisher mounting clips with a remover tool
(B), and then remove dash side finisher (1).
FRONT KICKING PLATE OUTER
Remove front kicking plate outer mounting clips with a remover tool
(A), and then remove kicking plate outer (1).
FRONT KICKING PLATE INNER
1.
Pull up front kicking plate inner, and disconnect pawls.
2.
Remove front kicking plate inner (1).
REAR KICKING PLATE OUTER
: Metal clip
JMJIA0081GB
JMJIA0106GB
: Clip
JMJIA0082GB
: Pawl
JMJIA0083GB
BODY SIDE TRIM
INT-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Remove rear kicking plate outer mounting clips with a remover tool
(A), and then remove kicking plate outer (1).
REAR KICKING PLATE INNER
1.
Pull up rear kicking plate inner, and disconnect pawls.
2.
Remove rear kicking plate inner (1).
FRONT BODY SIDE WELT
1.
Remove front kicking plate inner.
2.
Remove front body side welt.
REAR BODY SIDE WELT
1.
Remove rear kicking plate inner.
2.
Remove rear body side welt.
CENTER PILLAR LOWER GARNISH
1.
Remove front kicking plate inner.
2.
Remove rear kicking plate inner.
3.
Remove front body side welt.
4.
Remove rear body side welt.
5.
Remove center pillar lower garnish mounting metal clips with a
screwdriver (A), and then remove center pillar lower garnish (1).
CENTER PILLAR UPPER GARNISH
1.
Remove center pillar lower garnish.
2.
Remove front seat belt floor anchor bolt and front seat belt shoulder anchor bolt. Refer to
BELT RETRACTOR : Removal and Installation"
.
: Clip
JMJIA0084GB
: Pawl
JMJIA0085GB
: Metal clip
JMJIA0086GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст