Infiniti G35 (V35) Sedan. Manual — part 821
INT-8
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000000960429
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000000960430
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
Precaution for Work
INFOID:0000000000960431
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operation.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
PIIB3706J
PREPARATION
INT-9
< PREPARATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000000960432
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000000960433
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Location the noise
(J-43980)
NISSAN Squeak and Rattle
Kit
Repairing the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Location the noise
Power tool
SIIA0995E
PIIB1407E
INT-10
< ON-VEHICLE REPAIR >
DOOR FINISHER
ON-VEHICLE REPAIR
DOOR FINISHER
Exploded View
INFOID:0000000000960434
Removal and Installation
INFOID:0000000000960435
REMOVAL
FRONT AND REAR DOOR FINISHER
1.
Fully open door window.
1.
Power window switch finisher (front)
2.
Inside handle escutcheon
3.
Front door finisher
4.
Step lamp
5.
Grommet
6.
Front door panel
7.
Power window switch finisher (rear)
8.
Rear door finisher
9.
Rear door panel
10. Seat memory switch
Clip
Pawl
Metal clip
JMJIA0066GB
DOOR FINISHER
INT-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
2.
Remove inside handle escutcheon (1) with remover tool (A).
3.
Remove screw (A), located on the back side of inside handle
escutcheon.
4.
Pull up power window switch finisher (1) with remover tool (A).
5.
Disconnect power window switch connector, and then remove
power window switch finisher.
6.
Remove screws (A), located on the back side of power window
finisher.
7.
Remove step lamp (1). Refer to
INL-100, "Removal and Installa-
: Pawl
JMJIA0073GB
JMJIA0074GB
: Pawl
JMJIA0075GB
JMJIA0076GB
JMJIA0077GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст