Infiniti G35 (V35) Sedan. Manual — part 720
FRONT STABILIZER
FSU-37
< ON-VEHICLE REPAIR >
[AWD]
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
FRONT STABILIZER
Exploded View
INFOID:0000000000957808
Removal and Installation
INFOID:0000000000957809
REMOVAL
1.
Remove tires with power tool.
2.
Remove under cover with power tool.
3.
Remove the mounting nut on the lower side of stabilizer connecting rod with power tool, and then remove
stabilizer connecting rod from stabilizer bar.
4.
Remove the mounting nuts of stabilizer clamp, and then remove stabilizer clamp and stabilizer bushing.
5.
Remove stabilizer bar.
INSTALLATION
Install in the reverse order of removal.
Inspection
INFOID:0000000000957810
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks
or damage. Replace it if a malfunction is detected.
FSU-38
< ON-VEHICLE REPAIR >
[AWD]
FRONT SUSPENSION MEMBER
FRONT SUSPENSION MEMBER
Exploded View
INFOID:0000000000957811
Removal and Installation
INFOID:0000000000957812
REMOVAL
1.
Remove tire with power tool.
2.
Remove under cover with power tool.
3.
Remove front cross bar.
4.
Separate steering gear assembly and lower joint. Refer to
ST-27, "2WD : Removal and Installation"
.
5.
Remove steering outer socket from steering knuckle. Refer to
ST-34, "AWD : Removal and Installation"
6.
Remove wheel sensor from steering knuckle. Refer to
BRC-101, "REAR SENSOR ROTOR : Removal
7.
Remove shock absorber. Refer to
FSU-29, "Removal and Installation"
8.
Remove front stabilizer. Refer to
FSU-17, "Removal and Installation"
.
9.
Install engine slinger, and then hoist engine.
10. Remove transverse link from front suspension member with power tool. Refer to
.
11. Remove steering hydraulic piping bracket and steering gear from front suspension member. Refer to
12. Set suitable jack front suspension member.
13. Remove mounting nuts between engine mounting insulator and from suspension member. Refer to
82, "AWD : Removal and Installation"
.
14. Remove mounting bolts and nuts of front suspension member with power tool.
15. Gradually lower jack to remove front suspension assembly from vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of installation position between front suspension member and transverse links (rub-
ber bushing) under unladen condition with tires on level ground.
Inspection
INFOID:0000000000957813
INSPECTION AFTER REMOVAL
Check the front suspension member for significant deformation, cracks, or damages. Replace if necessary.
INSPECTION AFER INSTALLATION
• Check wheel alignment. Refer to
.
• Adjust the neutral position of the steering angle sensor after checking the wheel alignment. Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
FRONT SUSPENSION ASSEMBLY
FSU-39
< REMOVAL AND INSTALLATION >
[AWD]
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
REMOVAL AND INSTALLATION
FRONT SUSPENSION ASSEMBLY
Exploded View
INFOID:0000000000957814
JPEIA0002GB
FSU-40
< REMOVAL AND INSTALLATION >
[AWD]
FRONT SUSPENSION ASSEMBLY
Removal and Installation
INFOID:0000000000957815
REMOVAL
Remove suspension assembly with engine assembly from vehicle. Refer to
INSTALLATION
Install in the reverse order of removal.
Inspection
INFOID:0000000000957816
INSPECTION AFTER REMOVAL
• Check wheel alignment. Refer to
• Adjust the neutral position of the steering angle sensor after checking the wheel alignment. Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
• Check wheel sensor harness for proper connection. Refer to
BRC-100, "Removal and Installation"
.
1.
Gasket
2.
Shock absorber mounting bracket
3.
Bound bumper
4.
Rubber seat
5.
Coil spring
6.
Shock absorber
7.
Stopper rubber
8.
Upper link
9.
Steering knuckle
10. Cotter pin
11. Insulator
12. Transverse link
13. Stabilizer bar
14. Stabilizer connecting rod
15. Stabilizer bushing
16. Stabilizer clamp
17. Front cross bar
18. Front suspension member
Refer to
for symbols in the figure.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст