Infiniti G35 (V35) Sedan. Manual — part 719
TRANSVERSE LINK
FSU-33
< ON-VEHICLE REPAIR >
[AWD]
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
TRANSVERSE LINK
Exploded View
INFOID:0000000000957802
Removal and Installation
INFOID:0000000000957803
REMOVAL
1.
Remove tires with power tool.
2.
Remove under cover with power tool.
3.
Remove shock absorber. Refer to
FSU-29, "Removal and Installation"
4.
Remove front crossbar.
5.
Remove transverse link from steering knuckle. Refer to
ST-34, "AWD : Removal and Installation"
.
6.
Set suitable jack under transverse link.
7.
Remove mounting bolts and nuts, and then remove transverse link.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Never tap on the ball joint cap of the stabilizer connecting rod with a hammer or a similar item when
inserting the stabilizer connecting rod into the transverse link.
• Perform final tightening of bolts and nuts at the front suspension member installation and shock absorber
lower side (rubber bushing), under unladen conditions with tires on level ground.
Inspection
INFOID:0000000000957804
INSPECTION AFTER REMOVAL
Visual Inspection
Check the following:
• Transverse link and bushing for deformation, cracks or damage. Replace it if a malfunction is detected.
• Ball joint boot for cracks or other damage, and also for grease leakage. Replace it if a malfunction is
detected.
Ball Joint Inspection
Manually move ball stud to confirm it moves smoothly with no binding.
Swing Torque Inspection
NOTE:
Before measurement, move ball stud at least ten times by hand to check for smooth movement.
• Hook a spring balance (A) at cotter pin mounting hole. Confirm
spring balance measurement value is within specifications when
ball stud begins moving.
- If it is outside the specified range, replace transverse link assem-
bly.
Rotating Torque Inspection
Standard
Swing toque
JPEIA0005ZZ
FSU-34
< ON-VEHICLE REPAIR >
[AWD]
TRANSVERSE LINK
• Attach mounting nut to ball stud. Make sure that rotating torque is
within specifications with a preload gauge (A) [SST: 3127S000 (J-
25765-A)].
- If it is outside the specified range, replace transverse link assem-
bly.
Axial End Play Inspection
• Move tip of ball stud in axial direction to check for looseness.
- If it is outside the specified range, replace transverse link assembly.
INSPECTION AFTER INSTALLATION
• Check wheel alignment. Refer to
• Adjust neutral position of steering angle sensor after checking wheel alignment. Refer to
MENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
Standard
Rotating toque
: Refer to
.
PDIA1258E
Standard
Axial end play
:Refer to
.
UPPER LINK
FSU-35
< ON-VEHICLE REPAIR >
[AWD]
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
UPPER LINK
Exploded View
INFOID:0000000000957805
Removal and Installation
INFOID:0000000000957806
REMOVAL
1.
Remove tires from with power tool.
2.
Remove shock absorber. Refer to
FSU-40, "Removal and Installation"
3.
Remove mounting bolts and nuts with power tool, and then remove upper link from steering knuckle.
4.
Remove mounting bolts and nuts, and then remove upper link and stopper rubber.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of bolts and nuts at the vehicle installation position (rubber bushing), under unladen
conditions with tires on level ground.
Inspection
INFOID:0000000000957807
INSPECTION AFTER REMOVAL
Visual Inspection
Check the following:
• Upper link and bushing for deformation, cracks or damage. Replace it if a malfunction is detected.
• Ball joint boot for cracks or other damage, and also for grease leakage. Replace it if a malfunction is
detected.
Ball Joint Inspection
Manually move ball stud to confirm it moves smoothly with no binding.
Swing Torque Inspection
NOTE:
Before measurement, move ball stud at least ten times by hand to check for smooth movement.
• Hook a spring balance (A) at cutout on ball stud. Confirm spring
balance measurement value is within specifications when ball stud
begins moving.
- If it is outside the specified range, replace upper link assembly.
Rotating Torque Inspection
• Attach mounting nut to ball stud. Make sure that rotating torque is
within specifications with a preload gauge (A) [SST: ST3127S000
(J-25765-A)].
- If it is outside the specified range, replace upper link assembly.
Axial End Play Inspection
Standard
Swing torque
: Refer to
JPEIA0005ZZ
Standard
Rotarian torque
: Refer to
PDIA1258E
FSU-36
< ON-VEHICLE REPAIR >
[AWD]
UPPER LINK
• Move tip of ball stud in axial direction to check for looseness.
- If it is outside the specified range, replace upper link assembly.
INSPECTION AFTER INSTALLATION
• Check wheel alignment. Refer to
• Adjust neutral position of steering angle sensor after checking wheel alignment. Refer to
MENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
Standard
Axial end play
: Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст