Infiniti G35 (V35) Sedan. Manual — part 7
ADP-22
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
INPUT PARTS
Switches
Sensors
OUTPUT PARTS
SEAT SYNCHRONIZATION FUNCTION
Item
Function
Driver seat control unit
• Operates the specific seat motor with the signal from the power seat switch.
• Transmits the ignition switch signal (ACC/ON) via UART communication to the
automatic drive positioner control unit.
Automatic drive positioner control unit
Operates the specific motor with the signal from tilt & telescopic switch or door mir-
ror remote control switch.
BCM
Recognizes the following status and transmits it to the driver seat control unit via
CAN communication.
• Ignition position: ACC/ON
Item
Function
Power seat switch
The following switch is installed.
• Reclining switch
• Lifting switch (front)
• Lifting switch (rear)
• Sliding switch
The specific parts can be operated with the operation of each switch.
Tilt & telescopic switch
The following switch is installed.
• Tilt switch
• Telescopic switch
The specific parts can be operated with the operation of each switch.
Door mirror remote control switch
The following switch is installed.
• Mirror switch
• Changeover switch
The specific parts can be operated with the operation of each switch.
Item
Function
Tilt and telescopic sensor
Detect the up/down and left/right position of steering column.
Item
Function
Door mirror motor
(driverside/passenger side)
Move the outside mirror face upward/downward and leftward/rightward.
Tilt & telescopic motor
Move the steering column upward/downward and frontward/rearward.
Lifting motor (front)
Move the seat lifter (front) upward/downward.
Lifting motor (rear)
Move the seat lifter (rear) upward/downward.
Reclining motor
Tilt and raise up the seatback.
Sliding motor
Slide the seat frontward/rearward.
AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-23
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
SEAT SYNCHRONIZATION FUNCTION : System Diagram
INFOID:0000000000960595
SEAT SYNCHRONIZATION FUNCTION : System Description
INFOID:0000000000960596
OUTLINE
The steering column position and door mirror position is adjusted to the position automatically according to the
direction and distance of seat movement when performing the manual operation of sliding, reclining or lifting
(rear). This function saves adjusting the mirror and steering column when adjusting the seat.
NOTE:
• This function is set to OFF before delivery (initial setting).
• This function can be stopped by turning both or either of the entry/exit assist function (seat) and the entry/
exit assist function (steering) OFF. (only for AT models)
For the system setting procedure. Refer to
ADP-11, "SYSTEM SETTING : Description"
OPERATION PROCEDURE
1.
Turn ignition switch ON.
2.
Adjust seat position [sliding, reclining, lifting (rear)].
3.
The steering and outside mirror is adjusted automatically.
NOTE:
• The seat synchronization function will not operate if seat adjusting value is more than limit value.
• The seat synchronization function will not operate if the steering column or door mirror moves to the operat-
ing end while this function is operating. Perform memory function or drive the vehicle at vehicle speed of 7
km/h or more once to activate this function again.
• If the seat position is uncomfortable after the adjustment, seat position can be adjusted easily by memory
operation.
OPERATION CONDITION
Satisfy all of the following items. The seat synchronization function is not performed if these items are not sat-
isfied.
JMJIA0115GB
Item
Limit value
Seat sliding
76 [mm]
Seat reclining
9.1 [degrees]
Seat lifter (rear)
20 [mm]
ADP-24
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
DETAIL FLOW
Item
Request status
Ignition position
ON
System setting [Entry/exit assist function (seat/steering)]
ON
Switch inputs
• Power seat switch
• Tilt & telescopic switch
• Door mirror remote control switch
• Set switch
• Memory switch
OFF
(Not operated)
AT selector lever (only for AT model)
P position
Parking break (only for MT models)
Applied
Order
Input
Output
Control unit condition
1
—
—
Perform Manual operation [Sliding, reclining or lifting (rear)].
2
Sensors
[Sliding, reclining, lifting
(rear)]
—
The driver seat control unit judges the direction and distance of
seat movement according to the signal input from each seat sen-
sor during manual operation.
3
—
Motors
(Tilt, telescopic, out-
side mirror)
Driver seat control unit requests the operation to position accord-
ing to the direction and distance of seat movement to the automat-
ic drive positioner control unit via UART communication. The
automatic drive positioner control unit operates each motor.
Sensors
(Tilt, telescopic, outside
mirror)
—
Driver seat control unit stops the operation of each motor when the
value of each sensor that is input to automatic drive positioner con-
trol unit via UART communication reaches the target address.
AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-25
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
SEAT SYNCHRONIZATION FUNCTION : Component Parts Location
INFOID:0000000000960597
JMJIA0161GB
1.
BCM M118, M119, M122, M123
2.
Automatic drive positioner control unit
M51, M52
3.
Driver seat control unit B451, B452
4.
Unified meter and A/C amp. M67
5.
AV control unit
With NAVI M87, M88
Without NAVI M83, M85
6.
AT assembly connector F51
7.
Tilt & telescopic switch M31
8.
Key slot M22
9.
Tilt sensor M48
10. Telescopic sensor M48
11.
Seat memory switch D5
12. Door mirror remote control switch
D17
A.
Dash side lower (Passenger side)
B.
View with instrument driver lower
panel removed
C.
Backside of seat cushion (driver side)
D.
Behind cluster lid C
E.
AT assembly
(TCM is built in AT assembly)
F.
View with instrument driver lower
panel removed
G
View with steering column cover low-
er and upper removed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст