Infiniti G35 (V35) Sedan. Manual — part 8
ADP-26
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
SEAT SYNCHRONIZATION FUNCTION : Component Description
INFOID:0000000000960598
CONTROL UNITS
13. Front door switch (driver side) B16
14. AT device (detention switch) M137
15. Parking brake switch B14
16. Door mirror (driver side) D3
17. Telescopic motor M49
18. Tilt motor M49
H.
View with center console assembly
removed
I.
View with center console assembly
removed
J.
View with instrument driver lower
panel removed
19. Side support (seat cushion)
(Side support unit B420)
20. Reclining motor B454
21. Side support (seatback)
(Side support unit B420)
22. Side support unit B420
23. Reclining switch
(Power seat switch B459)
24. Sliding, lifting switch
(Power seat switch B459)
25. Side support switch (seat back side)
B419
26. Side support switch (cushion side)
B419
27. Sliding sensor B453
28. Lifting motor (front) B455
29. Sliding motor B461
30. Lifting motor (rear) B456
K.
View with seat cushion pad and seat-
back pad removed
L.
Backside of the seat cushion
JMJIA0162GB
JMJIA0164GB
AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-27
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
INPUT PARTS
Switches
Sensors
OUTPUT PARTS
MEMORY FUNCTION
Item
Function
Driver seat control unit
Operates the specific seat motor with the signal from the power seat switch.
Automatic drive positioner control unit
Operates the steering motor and door mirror with the instructions from the driver
seat control unit.
Item
Function
Power seat switch
The following switch is installed.
• Reclining switch
• Lifting switch (front)
• Lifting switch (rear)
• Sliding switch
The specific parts can be operated with the operation of each switch.
Item
Function
Door mirror sensor
(driver side/passenger side)
Detect the up/down and left/right position of outside mirror face.
Tilt and telescopic sensor
Detect the up/down and left/right position of steering column.
Lifting sensor (rear)
Detect the up/down position of seat lifter (rear).
Reclining sensor
Detect the tilt of seatback.
Sliding sensor
Detect the front/rear position of seat.
Item
Function
Door mirror motor
(driver side/passenger side)
Move the outside mirror face upward/downward and leftward/rightward.
Tilt & telescopic motor
Move the steering column upward/downward and frontward/rearward.
Lifting motor (rear)
Move the seat lifter (rear) upward/downward.
Reclining motor
Tilt and raise up the seatback.
Sliding motor
Slide the seat frontward/rearward.
ADP-28
< FUNCTION DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER SYSTEM
MEMORY FUNCTION : System Diagram
INFOID:0000000000960599
MEMORY FUNCTION : System Description
INFOID:0000000000960600
OUTLINE
The driver seat control unit can store the optimum driving positions (seat, steering column and door mirror
position) for 2 people. If the front seat position is changed, one-touch (pressing desired memory switch for
more than 0.5 second) operation allows changing to the other driving position.
NOTE:
Further information for the memory storage procedure. Refer to
ADP-10, "MEMORY STORING : Description"
OPERATION PROCEDURE
1.
Turn ignition switch ON
2.
Press desired memory switch for more than 0.5 second.
3.
Driver seat, steering and door mirror will move to the memorized position.
OPERATION CONDITION
Satisfy all of the following items. The memory function is not performed if these items are not satisfied.
DETAIL FLOW
JMJIA0163GB
Item
Request status
Ignition position
ON
Switch inputs
• Power seat switch
• Tilt & telescopic switch
• Door mirror control switch
• Set switch
• Memory switch
OFF
(Not operated)
AT selector lever (only for AT model)
P position
Parking break (only for MT models)
Applied
AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-29
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Order
Input
Output
Control unit condition
1
Memory switch
—
The memory switch signal is inputted to the automatic drive positioner
control unit when memory switch 1 or 2 is operated.
Memory switch signal is input to driver seat control unit via UART
communication.
2
—
Motors
(Seat, Steering,
door mirror)
Driver seat control unit operates each motor of seat when it recogniz-
es the memory switch pressed for 0.5 second or more and requests
each motor operation to automatic drive positioner control unit via
UART communication. The automatic drive positioner control unit op-
erates each motor.
Memory switch Indica-
tor
Driver seat control unit requests the flashing of memory indicator to
automatic drive positioner control unit via UART communication while
either of the motors is operating. The automatic drive positioner con-
trol unit illuminates the memory indicator.
3
Sensors
(Seat, steering col-
umn, door mirror)
—
Driver seat control unit judges the operating seat position with each
seat sensor input. The positions of the steering column and outside
mirror are monitored with each sensor signal that is input from auto
drive positioner control unit via UART communication. Driver seat
control unit stops the operation of each motor when each part reach-
es the recorded address.
4
—
Memory switch Indica-
tor
Driver seat control unit requests the illumination of memory indicator
to auto drive positioner control unit via UART communication after all
motors stop. The auto driving positioner control unit illuminates the
memory indicator for 5 seconds.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст