Infiniti G35 (V35) Sedan. Manual — part 312
CL-18
< REMOVAL AND INSTALLATION >
CSC (CONCENTRIC SLAVE CYLINDER)
CAUTION:
Assemble the components checking that the bracket (A) on
the CSC body and the nozzle (B) closely contact each other
before tightening the bolt. When assembled correctly, the
components should not move beyond the allowable loose-
ness of the connector on the CSC body.
7.
Install air bleeder valve to CSC tube and then tighten air bleeder
valve to the specified torque.
8.
Install transmission assembly to the vehicle. Refer to
9.
Bleed the air from the clutch hydraulic system. Refer to
JPDIB0022ZZ
CLUTCH DISC AND CLUTCH COVER
CL-19
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
CLUTCH DISC AND CLUTCH COVER
Exploded View
INFOID:0000000000956937
CAUTION:
• If transmission assembly is removed from the vehicle, always replace CSC (Concentric Slave Cylinder) body and CSC tube.
Return CSC body insert to original position to remove transmission assembly. Dust on clutch disc sliding parts may damage
seal of CSC body and may cause clutch fluid leakage.
• Be careful not to bring any grease to the clutch disc facing, pressure plate surface and flywheel surface.
• When installing, be careful that grease applied to main drive gear does not adhere to clutch disc.
• Do not clean in solvent on clutch disc.
• If flywheel is removed, align dowel pin with the smallest hole of flywheel. Refer to
EM-114, "Disassembly and Assembly"
.
Removal and Installation
INFOID:0000000000956938
CAUTION:
If transmission assembly is removed from the vehicle, always replace CSC (Concentric Slave Cylin-
der) body and CSC tube. Return CSC body insert to original position to remove transmission assem-
bly. Dust on clutch disc sliding parts may damage seal of CSC body and may cause clutch fluid
leakage.
REMOVAL
1.
Remove transmission assembly from the vehicle. Refer to
TM-26, "Removal and Installation"
2.
Loosen clutch cover mounting bolts with power tool.
3.
Remove clutch cover and clutch disc.
CAUTION:
Do not drop clutch disc.
INSTALLATION
1.
Clean clutch disc and main drive gear splines to remove grease and powder arisen from abrasion.
2.
Apply recommended grease to clutch disc and main drive gear splines.
CAUTION:
1.
Flywheel
2.
Clutch disc
3.
Clutch cover
4.
Main drive gear
A.
First step
B.
Final step
: Replace the parts as a set.
: Apply lithium-based grease including molybdenum disulphide.
Refer to
for symbols not described on the above.
JPDIB0024GB
CL-20
< REMOVAL AND INSTALLATION >
CLUTCH DISC AND CLUTCH COVER
Be sure to apply grease to the points specified. Otherwise, noise, poor disengagement, or damage
to the clutch may result. Excessive grease may cause slip or judder. And if it adheres to seal of
CSC body, it cause clutch fluid leakage. Wipe off excess grease. Wipe off any grease oozing from
the parts.
3.
Install clutch disc using the clutch aligning bar [SST:
ST20670000 (
—
)]
CAUTION:
If either clutch disc or clutch cover is needed to be
replaced, replace them as a set.
4.
Install clutch cover. Pre-tighten clutch cover mounting bolts.
CAUTION:
If either clutch disc or clutch cover is needed to be
replaced, replace them as a set.
5.
Tighten clutch cover mounting bolts evenly in two steps in the
order shown in the figure.
6.
Install transmission assembly to the vehicle. Refer to
Inspection
INFOID:0000000000956939
INSPECTION AFTER REMOVAL
CLUTCH DISC
• Measure circumferential runout relative to clutch disc center spline.
If it is outside the specification, replace clutch disc and clutch cover
as a set.
• Measure backlash to clutch disc spline and main drive gear spline
at the circumference of clutch disc. If outside the specification,
replace clutch disc and clutch cover as a set.
• Measure the depth to clutch disc facing rivet heads using calipers.
If it exceeds the allowable wear limit, replace clutch disc and clutch
cover as a set.
CLUTCH COVER
Check diaphragm spring lever claws for unevenness with the lever
still on the vehicle. If they exceed the tolerance, adjust lever height
using the diaphragm adjusting wrench [SST: ST20050240 (
—
)].
• Check clutch cover thrust ring for wear or breakage. If wear or
breakage is found, replace clutch disc and clutch cover as a set.
NOTE:
SCIA6797E
Runout limit/diameter of the
area to be measured
: Refer to
.
Maximum allowable spline
backlash (at outer edge of disc)
: Refer to
.
Facing wear limit (depth to the
rivet head)
: Refer to
.
SCL221
SCL229
Tolerance for diaphragm
spring lever unevenness
: Refer to
PCIB0276E
CLUTCH DISC AND CLUTCH COVER
CL-21
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
• Worn thrust ring will generate a beating noise when tapped at the rivet with a hammer.
• Broken thrust ring will make a clinking sound when cover is shaken up and down.
• If a trace of burn or discoloration is found on the clutch cover pressure plate to clutch disc contact surface,
repair the surface with sandpaper. If surface is damaged or distorted, replace clutch disc and clutch cover as
a set.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст