Infiniti G35 (V35) Sedan. Manual — part 434
DLN-170
< ON-VEHICLE REPAIR >
[REAR FINAL DRIVE: R200]
SIDE OIL SEAL
3.
Install side flange with the following procedure.
a.
Attach the protector [SST: KV38107900 (J-39352)] to side oil
seal.
b.
After the side flange is inserted and the serrated part of side
gear has engaged the serrated part of flange, remove the pro-
tector.
c.
Put a suitable drift on the center of side flange, then drive it until sound changes.
NOTE:
When installation is completed, driving sound of the side flange turns into a sound which seems to affect
the whole final drive.
d.
Confirm that the dimension of the side flange installation (Mea-
surement A) in the figure comes into the following.
4.
Install drive shaft. Refer to
RAX-9, "Removal and Installation"
.
5.
Install rear wheel sensor. Refer to
.
6.
Install center muffler. Refer to
EX-5, "Removal and Installation"
.
7.
When oil leaks while removing, check oil level after the installa-
tion. Refer to
.
SDIA0822E
Measurement “A”
: 326 – 328 mm (12.83 –
12.91 in)
SDIA1039E
REAR FINAL DRIVE ASSEMBLY
DLN-171
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REMOVAL AND INSTALLATION
REAR FINAL DRIVE ASSEMBLY
2WD
2WD : Exploded View
INFOID:0000000000957391
2WD : Removal and Installation
INFOID:0000000000957392
REMOVAL
1.
Remove center muffler with a power tool. Refer to
EX-5, "Removal and Installation"
.
2.
Remove rear stabilizer bar with a power tool. Refer to
RSU-15, "Removal and Installation"
.
3.
Remove propeller shaft from the final drive. Refer to
DLN-93, "Removal and Installation"
.
4.
Remove drive shaft from final drive with a power tool. Then sus-
pend it by wire etc. Refer to
RAX-9, "Removal and Installation"
.
5.
Remove breather hose from the final drive.
6.
Remove rear wheel sensor. Refer to
.
1.
Rear final drive assembly
2.
Upper stopper
3.
Lower stopper
4.
Washer
: Vehicle front
Refer to
JSDIA0025GB
SDIA1094E
DLN-172
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R200]
REAR FINAL DRIVE ASSEMBLY
7.
Set a suitable jack to rear final drive assembly.
CAUTION:
Never place a suitable jack on the rear cover (aluminum
case).
8.
Remove the mounting bolts and nuts connecting to the suspen-
sion member, and remove rear final drive assembly with a power
tool.
CAUTION:
Secure rear final drive assembly to a suitable jack while
removing it.
INSTALLATION
Note the following, and installation is in the reverse order of removal.
• When installing breather hoses (1), refer to the figure.
CAUTION:
Make sure there are no pinched or restricted areas on the
breather hose caused by bending or winding when installing
it.
- For installation, the vehicle side end shall be inserted to suspen-
sion member (2). Install metal connector (3) side of this hose to
rear cover by inserting it with aiming painted marking to the front of
vehicle.
• When oil leaks while removing final drive assembly, check oil level
after the installation. Refer to
AWD
AWD : Exploded View
INFOID:0000000000957393
AWD : Removal and Installation
INFOID:0000000000957394
JSDIA0026ZZ
: Vehicle front
PDIA0754E
1.
Rear final drive assembly
2.
Upper stopper
3.
Lower stopper
4.
Washer
: Vehicle front
Refer to
for symbols in the figure.
JSDIA0024GB
REAR FINAL DRIVE ASSEMBLY
DLN-173
< REMOVAL AND INSTALLATION >
[REAR FINAL DRIVE: R200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REMOVAL
1.
Remove center muffler with a power tool. Refer to
EX-5, "Removal and Installation"
.
2.
Remove rear stabilizer bar with a power tool. Refer to
RSU-15, "Removal and Installation"
.
3.
Remove propeller shaft from the final drive. Refer to
DLN-93, "Removal and Installation"
.
4.
Remove drive shaft from final drive with a power tool. Then sus-
pend it by wire etc. Refer to
RAX-9, "Removal and Installation"
.
5.
Remove breather hose from the final drive.
6.
Remove rear wheel sensor. Refer to
.
7.
Set a suitable jack to rear final drive assembly.
CAUTION:
Never place a suitable jack on the rear cover (aluminum
case).
8.
Remove the mounting bolts and nuts connecting to the suspen-
sion member, and remove rear final drive assembly with a power
tool.
CAUTION:
Secure rear final drive assembly to a suitable jack while
removing it.
INSTALLATION
Note the following, and installation is in the reverse order of removal.
• When installing breather hoses (1), refer to the figure.
CAUTION:
Make sure there are no pinched or restricted areas on the
breather hose caused by bending or winding when installing
it.
- For installation, the vehicle side end shall be inserted to suspen-
sion member (2). Install metal connector (3) side of this hose to
rear cover by inserting it with aiming painted marking to the front of
vehicle.
• When oil leaks while removing final drive assembly, check oil level
after the installation. Refer to
SDIA1094E
JSDIA0131ZZ
: Vehicle front
PDIA0754E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст