Infiniti G35 (V35) Sedan. Manual — part 1129
RSU-16
< ON-VEHICLE REPAIR >
REAR SUSPENSION MEMBER
REAR SUSPENSION MEMBER
Exploded View
INFOID:0000000000957845
Removal and Installation
INFOID:0000000000957846
REMOVAL
1.
Remove tires from vehicle with power tool.
2.
Remove brake caliper with power tool. Hang it in a place where it will not interfere with work. Refer to
53, "BRAKE CALIPER ASSEMBLY (FRONT CALIPER 1 PISTON TYPE) : Removal and Installation"
(front caliper 1 piston),
BR-57, "BRAKE CALIPER ASSEMBLY (FRONT CALIPER 2 PISTON TYPE) :
(front caliper 2 piston).
CAUTION:
Avoid depressing brake pedal while brake caliper is removed.
3.
Remove disc rotor. Refer to
BR-53, "BRAKE CALIPER ASSEMBLY (FRONT CALIPER 1 PISTON TYPE)
BR-57, "BRAKE CALIPER ASSEMBLY (FRONT CALI-
PER 2 PISTON TYPE) : Removal and Installation"
(front caliper 2 piston).
4.
Remove wheel sensor and sensor harness from axle assembly and suspension arm. Refer to
5.
Remove height sensor harness from rear suspension member (with xenon headlamp). Refer to
6.
Remove center muffler and main muffler. Refer to
EX-5, "Removal and Installation"
.
7.
Remove stabilizer bar. Refer to
RSU-15, "Removal and Installation"
.
8.
Remove drive shaft. Refer to
RAX-9, "Removal and Installation"
9.
Remove propeller shaft. Refer to
DLN-80, "Removal and Installation"
10. Remove harness from rear final drive and rear suspension member.
11. Remove final drive. Refer to
DLN-55, "Removal and Installation"
12. Remove parking brake cable mounting bolt and separate parking brake cable from vehicle and rear sus-
pension member. Refer to
PB-9, "Removal and Installation"
.
13. Remove mounting bolts in lower side of shock absorber.
14. Remove rear lower link and coil spring. Refer to
FSU-9, "Removal and Installation"
.
15. Set suitable jack under rear suspension member.
16. Remove mounting nuts rear suspension member.
17. Slowly lower jack, then remove rear suspension member, suspension arm, radius rod, front lower link and
axle from vehicle as a unit.
18. Remove mounting bolts and nuts, then remove suspension arm, front lower link, and radius rod from rear
suspension member.
INSTALLATION
Note the following, and install in the reverse order of the removal.
• Perform the final tightening of each of parts under unladen conditions, which were removed when removing
rear suspension assembly.
• Check wheel sensor harness for proper connection. Refer to
BRC-100, "Removal and Installation"
.
Inspection
INFOID:0000000000957847
INSPECTION AFTER REMOVAL
Check front suspension member for deformation, cracks, or any other damage. Replace if necessary.
INSPECTION AFTER INSTALLATION
• Check wheel alignment. Refer to
• Adjust neutral position of steering angle sensor after checking wheel alignment. Refer to
MENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
• Adjust parking brake operation (stroke).
PB-3, "PEDAL TYPE : Inspection and Adjustment"
REAR SUSPENSION ASSEMBLY
RSU-17
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REMOVAL AND INSTALLATION
REAR SUSPENSION ASSEMBLY
Exploded View
INFOID:0000000000957848
JPEIB0001GB
RSU-18
< REMOVAL AND INSTALLATION >
REAR SUSPENSION ASSEMBLY
Removal and Installation
INFOID:0000000000957849
REMOVAL
1.
Remove tire with power tool.
2.
Remove brake caliper with power tool. Hang it in a place where it will not interfere with work. Refer to
53, "BRAKE CALIPER ASSEMBLY (FRONT CALIPER 1 PISTON TYPE) : Removal and Installation"
(front caliper 1 piston type),
BR-57, "BRAKE CALIPER ASSEMBLY (FRONT CALIPER 2 PISTON TYPE)
(front caliper 2 piston type).
CAUTION:
Never depressing brake pedal while brake caliper is removed.
3.
Put matching marks on both disc rotor and the wheel hub and bearing assembly, and then remove disc
rotor. Refer to
BR-53, "BRAKE CALIPER ASSEMBLY (FRONT CALIPER 1 PISTON TYPE) : Removal
(front caliper 1 piston type),
BR-57, "BRAKE CALIPER ASSEMBLY (FRONT CALIPER 2
PISTON TYPE) : Removal and Installation"
(front caliper 2 piston type).
4.
Remove wheel sensor from rear final drive. Refer to
BRC-100, "Removal and Installation"
.
5.
Remove height sensor harness from rear suspension member (with xenon headlamp). Refer to
6.
Remove harness from rear final drive and rear suspension member.
7.
Remove center muffler. Refer to
EX-5, "Removal and Installation"
.
8.
Remove rear propeller shaft. Refer to
DLN-93, "Removal and Installation"
DLN-101, "Removal and Installation"
(AWD models).
9.
Separate parking brake cable from vehicle and rear suspension member. Refer to
PB-8, "LEVER TYPE : Removal and Installation"
10. Remove rear lower link and coil spring. Refer to
RSU-14, "Removal and Installation"
.
11. Remove mounting bolt on lower side of shock absorber. Refer to
RSU-9, "Removal and Installation"
12. Set suitable jack under rear final drive.
13. Gradually lowering jack, remove rear suspension assembly.
CAUTION:
Secure suspension assembly to a suitable jack while removing it.
INSTALLATION
Note the following, and install in the reverse order of the removal.
• Perform the final tightening of each of parts under unladen conditions, with tires on level ground.
• Check wheel sensor harness for proper connection. Refer to
BR-57, "BRAKE CALIPER ASSEMBLY
(FRONT CALIPER 2 PISTON TYPE) : Removal and Installation"
.
Inspection
INFOID:0000000000957850
INSPECTION AFTER REMOVAL
• Check the wheel alignment. Refer to
• Adjust neutral position of steering angle sensor after checking the wheel alignment. Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
• Adjust parking brake operation. Refer to
PB-3, "PEDAL TYPE : Inspection and Adjustment"
(pedal type),
PB-4, "LEVER TYPE : Inspection and Adjustment"
(lever type).
1.
Suspension arm
2.
Stopper rubber
3.
Stabilizer connecting rod mounting
bracket
4.
Stabilizer connecting rod
5.
Mount stopper
6.
Damper assembly
7.
Suspension member
8.
Stabilizer bar
9.
Stabilizer bushing
10. Stabilizer clamp
11. Upper seat
12. Coil spring
13. Ball seat
14. Rubber seat
15. Rear lower link
16. Front lower link
17. Radius rod
18. Cotter pin
19. Axle assembly
20. Shock absorber
21. Bound bumper cover
22. Shock absorber mounting bracket
23. Mounting seal
24. Cap
Refer to
for symbols in the figure.
SERVICE DATA AND SPECIFICATIONS (SDS)
RSU-19
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment
INFOID:0000000000957851
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Ball Joint
INFOID:0000000000957852
Wheel Height
INFOID:0000000000957853
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Applied model
2WD
AWD
Without 4WAS
With 4WAS
Camber
Degree minute (Decimal degree)
Minimum
–1
°
20
′
(–1.33
°
)
–1
°
25
′
(–1.42
°
)
–0
°
45
′
(–0.75
°
)
Nominal
–0
°
50
′
(–0.83
°
)
–0
°
55
′
(–0.92
°
)
–0
°
15
′
(–0.25
°
)
Maximum
–0
°
20
′
(–0.33
°
)
–0
°
25
′
(–0.42
°
)
0
°
15
′
(0.25
°
)
Total toe-in
Distance
Minimum
0 mm (0 in)
Nominal
2.8 mm (0.110 in)
Maximum
5.6 mm (0.220 in)
Angle (left wheel or right wheel)
Degree minute (Decimal degree)
Minimum
0
°
00
′
(0.00
°
)
Nominal
0
°
07
′
(0.12
°
)
Maximum
0
°
14
′
(0.23
°
)
Swing torque
0.5 - 3.4 N·m (0.06 - 0.34 kg-m, 5 - 30 in-lb)
Measurement on spring balance (cotter pinhole position)
8.1 - 54.8 N (0.83 - 5.6 kg, 1.82 - 12.32 lb)
Rotating torque
0.5 - 3.4 N·m (0.06 - 0.34 kg-m, 5 - 30 in-lb)
Axial end play
0 mm (0 in)
Applied model
2WD
AWD
Without 4WAS
With 4WAS
Tire
225/55R17
245/45R18
225/55R17
Rear (Hr)
707 mm (27.83 in)
707 mm (27.83 in)
705 mm (27.76 in)
723 mm (28.46 in)
SFA818A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст