Infiniti G35 (V35) Sedan. Manual — part 1128
RSU-12
< ON-VEHICLE REPAIR >
SUSPENSION ARM
• Attach the mounting nut to ball stud. Make sure that rotating torque
is within the specifications with a preload gauge (A)
[SST:ST3127S000 (J-25765-A)].
- If it is outside the specified range, replace suspension arm assem-
bly.
Axial End Play Inspection
• Move tip of ball stud in axial direction to check for looseness.
- If it is outside the specified range, replace suspension arm assembly.
INSPECTION AFTRE INSTALLATION
• Check wheel alignment. Refer to
• Adjust neutral position of steering angle sensor after checking the wheel alignment. Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
Standard
Rotating torque
: Refer to
.
PDIA1258E
Standard
Axial end play
: Refer to
.
RADIUS ROD
RSU-13
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
RADIUS ROD
Exploded View
INFOID:0000000000957836
Removal and Installation
INFOID:0000000000957837
REMOVAL
1.
Remove tire with power tool.
2.
Set suitable jack under axle assembly.
3.
Remove mounting bolts and nuts in axle side of radius rod with power tool.
4.
Remove mounting bolt in rear suspension member side of radius rod with power tool, then remove radius
rod.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of rear suspension member and axle installation position (rubber bushing), under
unladen conditions with tires on level ground.
Inspection
INFOID:0000000000957838
INSPECTION AFTER REMOVAL
Check radius rod and bushing for any deformation, cracks, or damage. Replace if there are.
INSPECTION AFTER INSTALLATION
• Check wheel alignment. Refer to
• Adjust neutral position of steering angle sensor after checking the wheel alignment. Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
RSU-14
< ON-VEHICLE REPAIR >
FRONT LOWER LINK
FRONT LOWER LINK
Exploded View
INFOID:0000000000957839
Removal and Installation
INFOID:0000000000957840
REMOVAL
1.
Remove tire with power tool.
2.
Set suitable jack under axle assembly to relieve the coil spring tension.
3.
Remove mounting bolts and nuts between front lower link and rear suspension member with power tool.
4.
Remove mounting bolts and nuts between front lower link and axle with power tool.
5.
Remove front lower link.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of rear suspension member and axle installation position (rubber bushing), under
unladen conditions with tires on level ground.
Inspection
INFOID:0000000000957841
INSPECTION AFTER REMOVAL
Check front lower link and bushing for any deformation, cracks, or damage. Replace if there are.
INSPECTION AFTER INSTALLATION
• Check wheel alignment. Refer to
• Adjust neutral position of steering angle sensor after checking the wheel alignment. Refer to Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
REAR STABILIZER
RSU-15
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR STABILIZER
Exploded View
INFOID:0000000000957842
Removal and Installation
INFOID:0000000000957843
REMOVAL
1.
Remove mounting bracket of center muffler and remove mounting rubber of main muffler. Refer to
2.
Remove lower side mounting nuts on stabilizer connecting rod and remove stabilizer connecting rod from
stabilizer bar with power tool.
3.
Remove mounting nuts on stabilizer clamp and remove stabilizer bar with power tool.
INSTALLATION
Install in the reverse order of removal.
Inspection
INFOID:0000000000957844
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks
or damage. Replace it if a malfunction is detected.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст