Infiniti G35 (V35) Sedan. Manual — part 741
GW-22
< ON-VEHICLE REPAIR >
REAR REGULATOR
REAR REGULATOR
Exploded View
INFOID:0000000000961530
Removal and Installation
INFOID:0000000000961531
REMOVAL
1.
Remove the rear door finisher. Refer to
INT-10, "Removal and Installation"
.
2.
Disconnect the rear door speaker connector.
3.
Remove the sealing screen.
4.
Remove the rear door cover inner. Refer to
INT-10, "Removal and Installation"
5.
Remove the door glass run on the partition sash side.
6.
Remove the partition sash fixing screw and bolts and remove
the partition sash.
1.
Partition sash
2.
Door glass
3.
Door glass run
4.
Partition glass run
5.
Partition glass
6.
Regulator assembly
7.
Power window motor
JMKIA0004ZZ
JMKIA0008ZZ
REAR REGULATOR
GW-23
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
7.
Operate the power window switch to raise/lower the door win-
dow until the glass mounting bolts can be seen.
8.
Remove the glass mounting bolts.
9.
Raise up the door glass and hold with a suction lifter.
10. Disconnect the connector for the regulator assembly.
11. Remove the regulator mounting bolts, and remove the regulator
from the door panel.
INSTALLATION
Install in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000000961532
DISASSEMBLY
Remove power window motor from regulator assembly.
ASSEMBLY
Assemble in the reverse order of disassembly.
Inspection and Adjustment
INFOID:0000000000961533
Inspection after Removal
Check the regulator assembly for the following items. If a malfunction is detected, replace or grease it.
• Gear wear
• Regulator deformation
• Grease condition for each sliding part
The arrows in the figure show the application points of the multi-pur-
pose grease.
SYSTEM INITIALIZATION OF THE ANTI-PINCH SYSTEM
If any of the following work has been done, initialize the system.
• Electric power sauce to power window switch or motor is interrupted by broken fuse or disconnecting battery
cable, etc.
JMKIA0009ZZ
JMKIA0011ZZ
JMKIA0012ZZ
GW-24
< ON-VEHICLE REPAIR >
REAR REGULATOR
• Removal and installation of the regulator assembly.
• Removal and installation of the motor from the regulator assembly.
• Removal and installation of the harness connector of the power window switch.
• Operation of the regulator assembly as a unit.
• Removal and installation of the door glass.
• Removal and installation of the door glass run.
Initialization
After installing each component to the vehicle, follow the steps below.
1.
Disconnect the minus terminal of battery or disconnect power window switch harness connector tempo-
rarily, then reconnect after at least 1 minute.
2.
Turn ignition switch ON.
3.
Open the window to its full width by operating the power window switch. (Exclude this procedure if the
window is already fully opened)
4.
Fully draw the power window switch in the up direction (auto close position) and hold, continue holding the
switch even when window is completely closed and then release after 3 seconds have passed.
5.
Inspection of the anti-pinch system function.
NOTE:
Initialization may be cancelled with continuous opening and closing operation. In this case, initialize the
system.
INSPECT THE FUNCTION OF THE ANTI-PINCH SYSTEM
1.
Fully open the door glass.
2.
Place a wooden piece (wooden hammer handle, etc.) at near fully closed position.
3.
Perform out fully closing operation with auto up switch.
• Check that the glass reverses without pinching the wooden piece, is lowered approximately 150 mm (5.91
in) or for 2 seconds and then stops.
• The glass should not be raised with power window main switch operated while it is reversing or lowering.
CAUTION:
• Do not inspect by pinching a part of worker's body, a hand, etc. Be careful not to be pinched.
• Check that the auto up function is normal before inspection following the system initialization.
FITTING INSPECTION
• Check that the glass is securely fit into the glass run groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.39 to 0.79 in)], and check that the clearance to the
sash is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator mounting
bolts, guide rail mounting bolts, and glass and carrier plate mounting bolts to correct the glass position.
HA-1
VENTILATION, HEATER & AIR CONDITIONER
C
D
E
F
G
H
J
K
L
M
SECTION
HA
A
B
HA
N
O
P
CONTENTS
HEATER & AIR CONDITIONING SYSTEM
BASIC INSPECTION . . . . . . . . .
DIAGNOSIS AND REPAIR WORKFLOW . . ..
Work Flow . . . . . . . . . . . . . . . .....
FUNCTION DIAGNOSIS . . . . . . . ...
REFRIGERATION SYSTEM . . . . . . . ...
System Diagram . . . . . . . . . . . . . ....
System Description . . . . . . . . . . . . ...
Component Parts Location . . . . . . . . . ....
Component Description . . . . . . . . . . .....
VARIABLE DISPLACEMENT COMPRESSOR
SYSTEM . . . . . . . . . . . . . . . ..
System Diagram . . . . . . . . . . . . . ....
System Description . . . . . . . . . . . . ...
SYMPTOM DIAGNOSIS . . . . . . . ..
REFRIGERATION SYSTEM SYMPTOMS . . .
SYMPTOM DIAGNOSIS PROCEDURE . . . . .
SYMPTOM DIAGNOSIS PROCEDURE : Trouble
Diagnosis For Unusual Pressure . . . . . . .
BOTH HIGH- AND LOW-PRESSURE SIDES ARE
TOO HIGH . . . . . . . . . . . . . . . . .
BOTH HIGH- AND LOW-PRESSURE SIDES
ARE TOO HIGH : Symptom Table . . . . . . ..
HIGH-PRESSURE SIDE IS TOO HIGH AND LOW-
PRESSURE SIDE IS TOO LOW . . . . . . . ...
HIGH-PRESSURE SIDE IS TOO LOW AND LOW-
PRESSURE SIDE IS TOO HIGH . . . . . . . ...
BOTH HIGH- AND LOW-PRESSURE SIDES ARE
TOO LOW . . . . . . . . . . . . . . . . ..
BOTH HIGH- AND LOW-PRESSURE SIDES
ARE TOO LOW : Symptom Table . . . . . . ...
LOW-PRESSURE SIDE SOMETIMES BECOMES
NEGATIVE . . . . . . . . . . . . . . . . .
LOW-PRESSURE SIDE SOMETIMES BE-
COMES NEGATIVE : Symptom Table . . . . .
LOW-PRESSURE SIDE BECOMES NEGATIVE . ..
LOW-PRESSURE SIDE BECOMES NEGATIVE :
Symptom Table . . . . . . . . . . . . . ...
PRECAUTION . . . . . . . . . . . ..
PRECAUTIONS . . . . . . . . . . . . .
Precaution Necessary for Steering Wheel Rota-
tion after Battery Disconnect . . . . . . . . ...
Precaution for Procedure without Cowl Top Cover .
Precautions For Xenon Headlamp Service . . . .
Working with HFC-134a (R-134a) . . . . . . ...
General Refrigerant Precaution . . . . . . . ...
Refrigerant Connection . . . . . . . . . . .
Service Equipment . . . . . . . . . . . . ..
COMPRESSOR . . . . . . . . . . . . .
General Precautions . . . . . . . . . . . .
LEAK DETECTION DYE . . . . . . . . ...
General Precautions . . . . . . . . . . . .
PREPARATION . . . . . . . . . . ...
PREPARATION . . . . . . . . . . . . .
Special Service Tool . . . . . . . . . . . .
Commercial Service Tool . . . . . . . . . .
Sealant or/and Lubricant . . . . . . . . . . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст