Infiniti G35 (V35) Sedan. Manual — part 740
GW-18
< ON-VEHICLE REPAIR >
FRONT REGULATOR
Initialization may be cancelled with continuous opening and closing operation. In this case, initialize the
system.
INSPECT THE FUNCTION OF THE ANTI-PINCH SYSTEM
1.
Fully open the door glass.
2.
Place a wooden piece (wooden hammer handle, etc.) at near fully closed position.
3.
Perform fully closing operation with auto up switch.
• Check that the glass reverses without pinching the wooden piece, is lowered approximately 150 mm (5.91
in) or for 2 seconds and then stops.
• The glass should not be raised with power window main switch operated while it is reversing or lowering.
CAUTION:
• Do not inspect by pinching a part of worker's body, a hand etc. Be careful not to be pinched.
• Check that the auto up function is normal before inspection following the system initialization.
FITTING INSPECTION
• Check that the glass is securely fit into the glass run groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.39 to 0.79 in)] and check that the clearance to the
sash is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator mounting
bolts, guide rail mounting bolts, and glass and guide rail mounting bolts to correct the glass position.
REAR DOOR GLASS
GW-19
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR DOOR GLASS
Exploded View
INFOID:0000000000961527
Removal and Installation
INFOID:0000000000961528
REMOVAL
1.
Remove the rear door finisher. Refer to
INT-10, "Removal and Installation"
.
2.
Disconnect the rear door speaker connector.
3.
Remove the sealing screen.
4.
Remove the rear door sash cover inner. Refer to
INT-10, "Removal and Installation"
5.
Remove the door glass run on the partition sash side.
6.
Remove the partition sash fixing screw and bolts, and remove
the partition sash.
1.
Partition sash
2.
Door glass
3.
Door glass run
4.
Partition glass run
5.
Partition glass
6.
Regulator assembly
7.
Power window motor
JMKIA0004ZZ
JMKIA0008ZZ
GW-20
< ON-VEHICLE REPAIR >
REAR DOOR GLASS
7.
Operate the power window switch to raise/lower the door win-
dow until the glass mounting bolts can be seen.
8.
Remove the glass mounting bolts.
9.
Remove the door glass from the inside of door panel.
10. Remove the door glass run.
11. Remove the partition glass from door panel.
INSTALLATION
Install in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000000961529
SYSTEM INITIALIZATION OF ANTI-PINCH SYSTEM
If any of the following work has been done, initialize the system.
• Electric power sauce to power window switch or motor is interrupted by broken fuse or disconnecting battery
cable, etc.
• Removal and installation of the regulator assembly.
• Removal and installation of the motor from the regulator assembly.
• Removal and installation of the harness connector of the power window switch.
• Operation of the regulator assembly as a unit.
• Removal and installation of the door glass.
• Removal and installation of the door glass run.
Initialization
After installing each component to the vehicle, follow the steps below.
1.
Disconnect the minus terminal of battery or disconnect power window switch harness connector tempo-
rarily, then reconnect after at least 1 minute.
2.
Turn ignition switch ON.
3.
Open the window to its full width by operating the power window switch. (Exclude this procedure if the
window is already fully opened)
4.
Fully draw the power window switch in the up direction (auto close position) and hold, continue holding the
switch even when window is completely closed and then release after 3 seconds have passed.
5.
Inspection of the anti-pinch system function.
NOTE:
Initialization may be cancelled with continuous opening and closing operation. In this case, initialize the
system.
INSPECT THE FUNCTION OF THE ANTI-PINCH SYSTEM
1.
Fully open the door glass.
2.
Place a wooden piece (wooden hammer handle, etc.) at near fully closed position.
JMKIA0009ZZ
JMKIA0010ZZ
REAR DOOR GLASS
GW-21
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
3.
Perform fully closing operation with auto up switch.
• Check that the glass reverses without pinching the wooden piece, is lowered approximately 150 mm (5.91
in) or for 2 seconds and then stops.
• The glass should not be raised with power window main switch operated while it is reversing or lowering.
CAUTION:
• Do not inspect by pinching a part of worker's body, a hand, etc. Be careful not to be pinched.
• Check that the auto up function is normal before inspection following the system initialization.
FITTING INSPECTION
• Check that the glass is securely fit into the glass run groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.39 to 0.79 in)], and check that the clearance to the
sash is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator mounting
bolts, guide rail mounting bolts, and glass and carrier plate mounting bolts to correct the glass position.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст