Infiniti G35 (V35) Sedan. Manual — part 1103
PWO-6
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000000963856
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PWO
CIGARETTE LIGHTER
PWO-7
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ON-VEHICLE REPAIR
CIGARETTE LIGHTER
Exploded View
INFOID:0000000000963857
Removal and Installation
INFOID:0000000000963858
REMOVAL
1.
Remove console finisher. Refer to
IP-12, "Removal and Installation"
2.
Remove screws (A) from reverse side cigarette lighter socket
(1).
3.
Pull out cigarette lighter (1).
4.
Pull out the cigarette lighter socket (2) by pushing the cigarette
lighter ring pawl (C) from the cigarette lighter socket hole
(square).
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
1
: Cigarette lighter
2
: Cigarette lighter socket
3
: Cigarette lighter ring
JPLIA0097ZZ
JPLIA0096ZZ
3
: Cigarette lighter ring
A
: Cut out
B
: Hole (square)
JPLIA0108ZZ
1
: Cigarette lighter
2
: Cigarette lighter socket
3
: Cigarette lighter ring
A
: Cut out
B
: Hole (square)
C
: Pawl
JPLIA0108ZZ
PWO-8
< ON-VEHICLE REPAIR >
CIGARETTE LIGHTER
Align the cigarette lighter socket and cigarette lighter ring cut out.
PWO
POWER SOCKET
PWO-9
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
POWER SOCKET
Exploded View
INFOID:0000000000963859
Removal and Installation
INFOID:0000000000963860
REMOVAL
1.
Remove rear upper console assembly. Refer to
IP-26, "Disassembly and Assembly"
.
2.
Disconnect power socket connector (A).
3.
Pull out the Inner socket (2) by pushing the ring pawl (B) from
the Inner socket hole (square).
4.
Remove ring (1) from console box while pressing pawls.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Align the Inner socket and the ring cut out.
1
: Ring
2
: Inner socket
JPLIA0098ZZ
C
: Cut out
D
: Hole (square)
JPLIA0109ZZ
1
: Ring
2
: Inner socket
A
: Power socket connector
B
: Pawl
C
: Cut out
D
: Hole (square)
JPLIA0109ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст