Infiniti G35 (V35) Sedan. Manual — part 1396

TM-276

< REMOVAL AND INSTALLATION >

[5AT: RE5R05A]

TRANSMISSION ASSEMBLY

6.

Remove heat insulator.

7.

Remove rear propeller shaft. Refer to

DLN-93, "Exploded View"

.

8.

Remove suspension member stay. Refer to

FSU-19, "Exploded View"

.

9.

Remove exhaust mounting bracket. Refer to

EX-5, "Exploded View"

.

10. Disconnect heated oxygen sensor 2 harness connectors (A).

11. Remove heated oxygen sensor 2 harness (B) from clips (1).

12. Remove bracket (2) from transmission assembly.

13. Remove control rod. Refer to

TM-236, "2WD : Exploded View"

.

14. Remove crankshaft position sensor (POS) from A/T assembly.

Refer to

EM-114, "Exploded View"

.

CAUTION:

• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings, etc. to get on the sensor's front edge magnetic area.
• Do not place in an area affected by magnetism.

15. Remove starter motor. Refer to

STR-15, "Exploded View"

.

16. Remove rear plate cover. Refer to

EM-41, "Exploded View (2WD)"

.

17. Turn crankshaft, and remove the four tightening bolts for drive

plate and torque converter.

CAUTION:

When turning the crankshaft, turn it clockwise as viewed
from the front of the engine.

18. Support A/T assembly with a transmission jack.

CAUTION:

When setting the transmission jack, be careful not to allow
it to collide against the drain plug.

19. Remove rear engine mounting member with power tool. Refer to

EM-77, "2WD : Exploded View"

.

20. Remove engine mounting insulator (rear). Refer to

EM-77,

"2WD : Exploded View"

.

21. Remove dynamic damper. Refer to

EM-77, "2WD : Exploded View"

.

22. Disconnect A/T assembly harness connector.

23. Remove air breather hose. Refer to

TM-268, "2WD : Exploded View"

.

24. Remove A/T fluid charging pipe from A/T assembly.

25. Remove O-ring from A/T fluid charging pipe.

26. Disconnect fluid cooler tube from A/T assembly.
27. Plug up openings such as the A/T fluid charging pipe hole, etc.

28. Remove bolts fixing A/T assembly to engine assembly with power tool.

29. Remove A/T assembly from vehicle.

CAUTION:

• Secure torque converter to prevent it from dropping.
• Secure A/T assembly to a transmission jack.

INSTALLATION

: Vehicle front

: Bolt

SCIA8269E

JPDIA0044ZZ

SCIA0499E

TRANSMISSION ASSEMBLY

TM-277

< REMOVAL AND INSTALLATION >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Install the removed parts in the reverse order of the removal, while paying attention to the following work.
• When installing A/T assembly to the engine assembly, attach the

fixing bolts in accordance with the following standard.

• Align the positions of tightening bolts for drive plate with those of

the torque converter, and temporarily tighten the bolts. Then,
tighten the bolts with the specified torque.

CAUTION:

• When turning crankshaft, turn it clockwise as viewed from the

front of the engine.

• When tightening the tightening bolts for the torque converter

after fixing the crankshaft pulley bolts, be sure to confirm the
tightening torque of the crankshaft pulley mounting bolts.
Refer to

EM-48, "Exploded View"

.

• After converter is installed to drive plate, rotate crankshaft

several turns and check to be sure that A/T rotates freely with-
out binding.

• Install crankshaft position sensor (POS). Refer to

EM-114, "Exploded View"

.

2WD : Inspection

INFOID:0000000000957182

INSPECTION AFTER INSTALLATION

• Installation and Inspection of Torque Converter
- After inserting a torque converter to a A/T, be sure to check dis-

tance (A) to ensure it is within the reference value limit.

• After completing installation, check the following item.
- A/T fluid leakage and A/T fluid level. Refer to

TM-217, "Inspection"

.

- A/T position. Refer to

TM-230, "2WD : Inspection and Adjustment"

.

AWD

AWD : Exploded View

INFOID:0000000000957183

A

: View from vehicle front

: Transmission to engine

: Engine to transmission

Bolt No.

B

C

Number of bolts

8

4

Bolt length
mm (in)

65 (2.56)

35 (1.38)

Tightening torque
N·m (kg-m, ft-lb)

75 (7.7, 55)

46.6 (4.8, 34)

JPDIA0043ZZ

JPDIA0044ZZ

B

: Scale

C

: Straightedge

Distance (A)

: Refer to

TM-354, "Torque Converter"

JPDIA0042ZZ

TM-278

< REMOVAL AND INSTALLATION >

[5AT: RE5R05A]

TRANSMISSION ASSEMBLY

AWD : Removal and Installation

INFOID:0000000000957184

REMOVAL

CAUTION:

• When removing the A/T assembly from engine, first remove the crankshaft position sensor (POS)

from the A/T assembly.

• Be careful not to damage sensor edge.
1.

Disconnect the battery cable from the negative terminal.

2.

Remove A/T fluid level gauge.

3.

Remove air cleaner case (RH). Refer to

EM-25, "Exploded View"

.

4.

Remove engine under cover with power tool.

5.

Remove exhaust front tube and center muffler and with power tool. Refer to

EX-5, "Exploded View"

.

6.

Remove heat insulator.

7.

Remove rear propeller shaft. Refer to

DLN-101, "Exploded View"

.

8.

Remove front cross bar with power tool. Refer to

FSU-39, "Exploded View"

.

9.

Remove exhaust mounting bracket. Refer to

EX-5, "Exploded View"

.

1.

A/T fluid level gauge

2.

A/T fluid charging pipe

3.

O-ring

4.

Copper washer

5.

A/T fluid cooler tube

6.

Bracket

7.

Bracket

8.

Bracket

9.

A/T assembly

A.

For tightening torque, Refer to

TM-

275, "2WD : Removal and Installa-
tion"

.

Refer to

GI-4, "Components"

for symbols in the figure.

JPDIA0048GB

TRANSMISSION ASSEMBLY

TM-279

< REMOVAL AND INSTALLATION >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

10. Disconnect heated oxygen sensor 2 harness connectors (A).

11. Remove heated oxygen sensor 2 harness (B) from clips (1).
12. Remove bracket (2) from transmission assembly.

13. Remove three way catalyst (right bank). Refer to

EX-5, "Exploded View"

.

14. Remove front propeller shaft. Refer to

DLN-80, "Exploded View"

.

15. Remove control rod. Refer to

TM-236, "AWD : Exploded View"

.

16. Remove crankshaft position sensor (POS) from A/T assembly. Refer to

EM-114, "Exploded View"

.

CAUTION:

• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings, etc. to get on the sensor's front edge magnetic area.
• Do not place in an area affected by magnetism.

17. Remove starter motor. Refer to

STR-15, "Exploded View"

.

18. Remove rear plate cover. Refer to

EM-41, "Exploded View (AWD)"

.

19. Turn crankshaft, and remove the four tightening bolts for drive

plate and torque converter.

CAUTION:

When turning the crankshaft, turn it clockwise as viewed
from the front of the engine.

20. Support A/T assembly with a transmission jack.

CAUTION:

When setting the transmission jack, be careful not to allow
it to collide against the drain plug.

21. Remove rear engine mounting member with power tool. Refer to

EM-81, "AWD : Exploded View"

.

22. Remove engine mounting insulator (rear). Refer to

EM-81,

"AWD : Exploded View"

.

23. Remove dynamic damper. Refer to

EM-81, "AWD : Exploded View"

.

24. Disconnect A/T assembly harness connector.
25. Remove air breather hose. Refer to

TM-269, "AWD : Exploded View"

.

26. Remove A/T fluid charging pipe from A/T assembly.

27. Remove O-ring from A/T fluid charging pipe.
28. Disconnect fluid cooler tube from the A/T assembly.

29. Plug up openings such as the A/T fluid charging pipe hole, etc.

30. Remove bolts fixing A/T assembly to engine assembly with power tool.
31. Remove A/T assembly with transfer assembly from vehicle.

CAUTION:

• Secure torque converter to prevent it from dropping.
• Secure A/T assembly to a transmission jack.

32. Remove transfer assembly from A/T assembly with power tool.

: Vehicle front

: Bolt

SCIA8269E

JPDIA0044ZZ

SCIA2203E