Infiniti G35 (V35) Sedan. Manual — part 1497
WASHER LEVEL SWITCH
WW-81
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WASHER LEVEL SWITCH
Removal and Installation
INFOID:0000000000962667
The washer level switch must be replaced together with the washer tank as an assembly. Refer to
WW-82
< ON-VEHICLE REPAIR >
FRONT WASHER NOZZLE AND TUBE
FRONT WASHER NOZZLE AND TUBE
Hydraulic Layout
INFOID:0000000000962668
Removal and Installation
INFOID:0000000000962669
REMOVAL
1.
Open the hood.
2.
Use the stop point of washer nozzle (1) as the support point and
rotate nozzle to remove it from body, while pushing nozzle spray
point side along the hood.
CAUTION:
• Be careful not to brake the seal rubber bonded to the
washer nozzle.
3.
Remove the seal rubber from the washer nozzle.
4.
Remove the washer tube (2) from the washer nozzle.
INSTALLATION
1.
Install washer tube in nozzle.
2.
Install the seal rubber.
NOTE:
When the washer nozzle is removed, bond the seal rubber to the washer nozzle using commercially avail-
able instantaneous adhesive
3.
Install the washer nozzle to the hood.
4.
Adjust the washer nozzle spray position.Refer to
WW-82, "Inspection and Adjustment"
.
CAUTION:
The spray positions differ, check that left and right nozzles are installed correctly.
Inspection and Adjustment
INFOID:0000000000962670
INSPECTION
1.
Seal rubber
2.
Washer nozzle
3.
Washer tube
4.
Washer tank
: Clip
JPLIA0074ZZ
JPLIA0075ZZ
FRONT WASHER NOZZLE AND TUBE
WW-83
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Washer Nozzle Inspection
Check that air can pass through the hose by blowing forward (toward
the nozzle), and check that air cannot pass through by sucking.
ADJUSTMENT
Washer Nozzle Spray Position Adjustment
Adjust spray positions to match the positions shown in the figure.
Unit: mm (in.)
Insert a needle or similar object (A) into the spray opening (1) and
move up/down and left/right to adjust the spray position.
NOTE:
If wax or dust gets into the nozzle, remove wax or dust with a needle
or small pin.
JPLIA0084ZZ
1
: Black printed frame line
: Vehicle front
Spray
position
H (Height)
L (Width)
φ
(Spray point area)
A
280 (11.02)
396 (15.59)
80 (3.15)
B
320 (12.6)
277 (10.91)
80
×
153 (3.15
×
6.02)
C
261 (10.28)
114 (4.49)
80
×
175 (3.15
×
6.89)
D
267 (10.51)
123 (4.84)
80
×
177 (3.15
×
6.97)
E
321 (12.64)
336 (13.23)
80
×
160 (3.15
×
6.30)
F
239 (9.41)
477 (18.78)
80
×
126 (3.15
×
4.96)
JPLIA0073ZZ
JPLIA0083ZZ
WW-84
< ON-VEHICLE REPAIR >
FRONT WIPER ARM
FRONT WIPER ARM
Exploded View
INFOID:0000000000962671
Removal and Installation
INFOID:0000000000962672
REMOVAL
1.
Operate the front wiper to move it to the auto stop position.
2.
Open the hood.
3.
Remove wiper arm cap.
4.
Remove the wiper arm mounting nut.
5.
Raise wiper arm, and remove wiper arm from the vehicle.
INSTALLATION
1.
Clean wiper arm mount as shown in the figure to prevent nuts
from being loosened.
2.
Operate the front wiper motor to move the wiper to the auto stop position.
3.
Adjust the wiper blade position. Refer to
.
4.
Install the wiper arm by tightening the mounting nut.
5.
Inject the washer fluid.
6.
Operate the front wiper to move it to the auto stop position.
7.
Check that the wiper blades stop at the specified position.
8.
Attach wiper arm cap.
1.
Wiper blade (RH)
2.
Wiper arm (RH)
3.
Wiper arm cap
4.
Wiper arm (LH)
5.
Wiper blade (LH)
Refer to
for symbols in the figure.
JPLIA0085GB
ELH0717D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст