Infiniti G35 (V35) Sedan. Manual — part 715
FRONT STABILIZER
FSU-17
< ON-VEHICLE REPAIR >
[2WD]
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
FRONT STABILIZER
Exploded View
INFOID:0000000000957777
Removal and Installation
INFOID:0000000000957778
REMOVAL
1.
Remove tires with power tool.
2.
Remove under cover with power tool.
3.
Remove the mounting nut on the lower side of stabilizer connecting rod with power tool, and then remove
stabilizer connecting rod from stabilizer bar.
4.
Remove the mounting nuts of stabilizer clamp, and then remove stabilizer clamp and stabilizer bushing.
5.
Remove stabilizer bar.
INSTALLATION
Install in the reverse order of removal.
Inspection
INFOID:0000000000957779
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks
or damage. Replace it if a malfunction is detected.
FSU-18
< ON-VEHICLE REPAIR >
[2WD]
FRONT SUSPENSION MEMBER
FRONT SUSPENSION MEMBER
Exploded View
INFOID:0000000000957780
Removal and Installation
INFOID:0000000000957781
REMOVAL
1.
Remove tire with power tool.
2.
Remove under cover with power tool.
3.
Remove suspension member stay with power tool.
4.
Separate steering gear assembly and lower joint. Refer to
ST-27, "2WD : Removal and Installation"
.
5.
Remove steering outer socket from steering knuckle.
6.
Remove wheel sensor from steering knuckle. Refer to
BRC-101, "REAR SENSOR ROTOR : Removal
7.
Remove stabilizer connecting rod from transverse link. Refer to
FSU-17, "Removal and Installation"
8.
Remove front stabilizer. Refer to
FSU-17, "Removal and Installation"
.
9.
Install engine slinger, and then hoist engine.
10. Remove transverse link from front suspension member with power tool. Refer to
.
11. Remove steering hydraulic piping bracket and steering gear from front suspension member. Refer to
12. Set suitable jack front suspension member.
13. Remove mounting nuts between engine mounting insulator and from suspension member. Refer to
77, "2WD : Removal and Installation"
.
14. Remove mounting bolts and nuts of front suspension member with power tool.
15. Gradually lower jack to remove front suspension assembly from vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of installation position between front suspension member and transverse links (rub-
ber bushing) under unladen condition with tires on level ground.
Inspection
INFOID:0000000000957782
INSPECTION AFTER REMOVAL
Check the front suspension member for significant deformation, cracks, or damages. Replace if necessary.
INSPECTION AFER INSTALLATION
• Check wheel alignment. Refer to
• Adjust the neutral position of the steering angle sensor after checking the wheel alignment. Refer to "Steer-
ing".
FRONT SUSPENSION ASSEMBLY
FSU-19
< REMOVAL AND INSTALLATION >
[2WD]
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
REMOVAL AND INSTALLATION
FRONT SUSPENSION ASSEMBLY
Exploded View
INFOID:0000000000957783
JPEIA0001GB
FSU-20
< REMOVAL AND INSTALLATION >
[2WD]
FRONT SUSPENSION ASSEMBLY
Removal and Installation
INFOID:0000000000957784
REMOVAL
Remove suspension assembly with engine assembly from vehicle. Refer to
INSTALLATION
Install in the reverse order of removal.
Inspection
INFOID:0000000000957785
INSPECTION AFTER INSTALLATION
• Check wheel alignment. Refer to
• Adjust the neutral position of the steering angle sensor after checking the wheel alignment. Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
• Check wheel sensor harness for proper connection. Refer to
BRC-100, "Removal and Installation"
.
1.
Gasket
2.
Shock absorber mounting bracket
3.
Bound bumper
4.
Rubber seat
5.
Coil spring
6.
Shock absorber
7.
Insulator
8.
Transverse link
9.
Front suspension member
10. Suspension member stay
11. Stabilizer clamp
12. Stabilizer bushing
13. Stabilizer connecting rod
14. Stabilizer bar
15. Cotter pin
16. Steering knuckle
17. Upper link
18. Stopper rubber
Refer to
for symbols in the figure.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст