Infiniti G35 (V35) Sedan. Manual — part 1169
DIAGNOSIS SYSTEM (BCM)
SEC-31
< FUNCTION DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
ACTIVE TEST
Monitor Item
Condition
REQ SW-DR
Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW-AS
Indicates [ON/OFF] condition of door request switch (passenger side).
REQ SW-BD/TR
Indicates [ON/OFF] condition of trunk opener request switch.
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
CLUCH SW
Indicates [ON/OFF] condition of clutch switch.
BRAKE SW 1
Indicates [ON/OFF] condition of brake switch.
DETE/CANCL SW
Indicates [ON/OFF] condition of P position.
SFT PN/N SW
Indicates [ON/OFF] condition of P or N position.
S/L -LOCK
Indicates [ON/OFF] condition of steering lock (LOCK).
S/L -UNLOCK
Indicates [ON/OFF] condition of steering lock (UNLOCK).
S/L RELAY-F/B
Indicates [ON/OFF] condition of ignition switch.
UNLK SEN-DR
Indicates [ON/OFF] condition of driver door UNLOCK status.
PUSH SW -IPDM
Indicates [ON/OFF] condition of push-button ignition switch.
IGN RLY1 F/B
Indicates [ON/OFF] condition of ignition relay 1.
DETE SW -IPDM
Indicates [ON/OFF] condition of P position.
SFT PN -IPDM
Indicates [ON/OFF] condition of P or N position.
SFT P -MET
Indicates [ON/OFF] condition of P position.
SFT N -MET
Indicates [ON/OFF] condition of N position.
ENGINE STATE
Indicates [STOP/START/CRANK/RUN] condition of engine states.
S/L LOCK-IPDM
Indicates [ON/OFF] condition of steering lock (LOCK).
S/L UNLOCK-IPDM
Indicates [ON/OFF] condition of steering lock (UNLOCK).
S/L RELAY-REQ
Indicates [ON/OFF] condition of steering lock relay.
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h].
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or CVT by numerical value [Km/h].
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver side door status.
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger side door status.
KEY SW -SLOT
Indicates [ON/OFF] condition of key slot.
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the
numerical value start changing.
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored.
TRNK/HAT MNTR
Indicates [ON/OFF] condition of trunk lid.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
RKE-TR/BD
Indicates [ON/OFF] condition of TRUNK OPEN signal from Intelligent Key.
RKE-PANIC
Indicates [ON/OFF] condition of PANIC button of Intelligent Key.
RKE-P/W OPEN
Indicates [ON/OFF] condition of P/W DOWN signal from Intelligent Key.
RKE-MODE CHG
Indicates [ON/OFF] condition of MODE CHANGE signal from Intelligent Key.
Test item
Description
BATTERY SAVER
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.
PW REMOTO DOWN SET
This test is able to check power window down operation.
The power window down will be activated after “ON” on CONSULT-III screen is touched.
SEC-32
< FUNCTION DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
THEFT ALM
THEFT ALM : CONSULT-III Function (BCM - THEFT)
INFOID:0000000000961330
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation.
Intelligent Key warning buzzer sounds when “ON” on CONSULT-III screen is touched.
INSIDE BUZZER
This test is able to check warning chime in combination meter operation.
• Take away warning chime sounds when “TAKE OUT” on CONSULT-III screen is touched.
• Key warning chime sounds when “KEY WARN” on CONSULT-III screen is touched.
• P position warning chime sounds when “P RNG WARN” on CONSULT-III screen is touched.
• ACC warning chime sounds when “ACC WARN” on CONSULT-III screen is touched.
INDICATOR
This test is able to check warning lamp operation.
• “KEY” Warning lamp illuminates when “KEY IND ON” on CONSULT-III screen is touched.
• “KEY” Warning lamp flashes when “KEY IND FSH” on CONSULT-III screen is touched.
INT LAMP
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.
LCD
This test is able to check meter display information
• Engine start information displays when “BRAKE/P” on CONSULT-III screen is touched.
• Engine start information displays when “BRAKE/P/ON” on CONSULT-III screen is touched.
• Key ID warning displays when “KEY ID NG” on CONSULT-III screen is touched.
• Steering lock information displays when “STLCK RELES” on CONSULT-III screen is touched.
• P position warning displays when “P RNG IND” on CONSULT-III screen is touched.
• Intelligent Key insert information displays when “INSERT KEY” on CONSULT-III screen is
touched.
• Intelligent Key low battery warning displays when “KEY BAT LOW” on CONSULT-III screen is
touched.
• Take away through window warning displays when “TK AWAY WDW” on CONSULT-III screen
is touched.
• Take away warning display when “TAKE AWAY” on CONSULT-III screen is touched.
• OFF position warning display when “IGN OFF WARN” on CONSULT-III screen is touched.
TRUNK/GLASS HATCH
This test is able to check trunk lid opener actuator open operation.
This actuator opens when “ON” on CONSULT-III screen is touched.
FLASHER
This test is able to check security hazard lamp operation.
The hazard lamps will be activated after “ON” on CONSULT-III screen is touched.
HORN
This test is able to check horn operation.
The horn will be activated after “ON” on CONSULT-III screen is touched.
IGN CONT2
This test is able to check security hazard lamp operation.
The hazard lamps will be activated after “ON” on CONSULT-III screen is touched.
P RANGE
This test is able to check A/T device power supply
A/T device power is supplied when “ON” on CONSULT-III screen is touched.
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation.
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched.
LOCK INDCATOR
This test is able to check LOCK indicator in push-ignition switch operation.
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
ACC INDCATOR
This test is able to check ACC indicator in push-ignition switch operation.
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
IGNITION ON IND
This test is able to check INGITION ON indicator in push-ignition switch operation.
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
KEY SLOT ILLUMI
This test is able to check key slot illumination operation.
Key slot illumination flash when “ON” on CONSULT-III screen is touched.
Test item
Description
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function.
DIAGNOSIS SYSTEM (BCM)
SEC-33
< FUNCTION DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
DATA MONITOR
WORK SUPPORT
ACTIVE TEST
IMMU
IMMU : CONSULT-III Function (BCM - IMMU)
INFOID:0000000000961331
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
Diagnosis mode
Function Description
Monitored Item
Description
REQ SW-DR
Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW-AS
Indicates [ON/OFF] condition of door request switch (passenger side).
REQ SW-BD/TR
Indicates [ON/OFF] condition of trunk opener request switch.
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch
UNLK SEN-DR
Indicates [ON/OFF] condition of driver door UNLOCK status.
KEY SW -SLOT
Indicates [ON/OFF] condition of key slot.
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch LH.
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch RH.
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-BK
This is displayed even when it is not equipped.
CDL LOCK SW
Indicates [ON/OFF] condition of lock signal from door lock/unlock switch LH and RH.
CDL UNLOCK SW
Indicates [ON/OFF] condition of unlock signal from door lock/unlock switch LH and RH.
KEY CYL LK-SW
Indicates [ON/OFF] condition of lock signal from front door key cylinder switch.
KEY CYL UN-SW
Indicates [ON/OFF] condition of unlock signal from front door key cylinder switch.
KEY CYL SW-TR
This is displayed even when it is not equipped.
TR/BD OPEN SW
Indicates [ON/OFF] condition of trunk lid opener switch.
TRNK/HAT MNTR
Indicates [ON/OFF] condition of trunk room lamp switch.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
RKE-TR/BD
Indicates [ON/OFF] condition of TRUNK OPEN signal from Intelligent Key.
Test Item
Description
SECURITY ALARM SET
This mode is able to confirm and change security alarm ON-OFF setting.
THEFT ALM TRG
The switch which triggered vehicle security alarm is recorded. This mode is able to confirm and
erase the record of vehicle security alarm. The trigger data can be erased by touching “CLEAR” on
CONSULT-III screen.
Test Item
Description
THEFT IND
This test is able to check security indicator lamp operation. The lamp will be turned on when “ON”
on CONSULT-III screen is touched.
VEHICLE SECURITY HORN
This test is able to check vehicle security horn operation. The horns will be activated for 0.5 sec-
onds after “ON” on CONSULT-III screen is touched.
HEADLAMP(HI)
This test is able to check vehicle security lamp operation. The headlamps will be activated for 0.5
seconds after “ON” on CONSULT-III screen is touched.
FLASHER
This test is able to check vehicle security hazard lamp operation. The hazard lamps will be activat-
ed after “ON” on CONSULT-III screen is touched.
SEC-34
< FUNCTION DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
DATA MONITOR
ACTIVE TEST
Diagnosis mode
Function Description
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
Monitor item
Content
CONFRM ID ALL
Indicates [YET] at all time.
Switch to [DONE] when a registered Intelligent Key is inserted into the key slot.
CONFIRM ID4
CONFIRM ID3
CONFIRM ID2
CONFIRM ID1
TP 4
Indicates the number of ID which has been registered.
TP 3
TP 2
TP 1
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
KEY SW -SLOT
Indicates [ON/OFF] condition of key slot.
Test item
Description
THEFT IND
This test is able to check security indicator lamp operation.
The lamp will be turned on when “ON” on CONSULT-III screen touched.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст