Infiniti G35 (V35) Sedan. Manual — part 422
DLN-122
< DISASSEMBLY AND ASSEMBLY >
[FRONT FINAL DRIVE: F160A]
DIFFERENTIAL ASSEMBLY
DIFFERENTIAL ASSEMBLY
Exploded View
INFOID:0000000000957359
1.
Drive pinion lock nut
2.
Companion flange
3.
Front oil seal
4.
Pinion front bearing
5.
Drive pinion bearing adjusting wash-
er
6.
Drive pinion adjusting washer
7.
Gear carrier
8.
Pinion rear bearing
9.
Pinion height adjusting washer
10. Drive pinion
11.
Drive gear
12. Side oil seal (right side)
13. Side retainer
14. O-ring
15. Side bearing adjusting shim
16. Side bearing
17. Differential case
18. Breather connector
19. Dowel pin
20. Filler plug
21. Drain plug
22. Gasket
23. Carrier cover
24. Gear oil defense
25. Side gear thrust washer
26. Side gear
27. Circular clip
28. Pinion mate thrust washer
29. Pinion mate gear
30. Pinion mate shaft
31. Lock pin
32. Side bearing adjusting washer
33. Side oil seal (left side)
JSDIA0020GB
DIFFERENTIAL ASSEMBLY
DLN-123
< DISASSEMBLY AND ASSEMBLY >
[FRONT FINAL DRIVE: F160A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Disassembly
INFOID:0000000000957360
1.
Drain gear oil, if necessary.
2.
Remove carrier cover mounting bolts.
3.
Remove carrier cover to insert the seal cutter (A) [SST:
KV10111100 (J-37228)] between gear carrier and carrier cover.
CAUTION:
• Never damage the mating surface.
• Never insert flat-bladed screwdriver, this way damage the
mating surface.
4.
Remove side retainer.
5.
Remove side bearing adjusting shim.
6.
Remove O-ring from side retainer.
7.
Remove differential case assembly from gear carrier.
34. Side shaft bearing
35. Extension tube retainer
36. Side shaft oil seal
37. Dust sealed
38. Side shaft
A: Oil seal lip
B: Screw hole
:
Apply gear oil.
:
Apply anti-corrosion oil.
:
Apply Genuine Silicone RTV or equivalent. Refer to
GI-15, "Recommended Chemical Products and Sealants"
:
Apply Genuine Medium Strength Thread Locking Sealant or equivalent. Refer to
GI-15, "Recommended Chemical Prod-
.
Refer to
for symbols not described on the above.
PDIA0795J
PDIA0670E
PDIA0671E
DLN-124
< DISASSEMBLY AND ASSEMBLY >
[FRONT FINAL DRIVE: F160A]
DIFFERENTIAL ASSEMBLY
8.
Remove side oil seal (right side) from side retainer.
9.
Remove side bearing outer race with puller (A) [SST:
KV381054S0 (J-34286)].
10. Remove O-ring from gear carrier.
11. Remove side oil seal (left side) from gear carrier.
12. Remove side bearing outer race with puller (A) [SST:
KV381054S0 (J-34286)].
13. Remove side bearing inner race.
To prevent damage to bearing, engage puller jaws in groove
(
).
CAUTION:
• To prevent damage to the side bearing and drive gear,
place copper plates between these parts and vise.
• It is not necessary to remove side bearing inner race
except it is replaced.
PDIA0672E
PDIA0796J
PDIA0797J
A: Puller [SST: ST33051001 (J-22888-20)]
B: Base [SST: ST33061000 (J-8107-2)]
PDIA0758J
DIFFERENTIAL ASSEMBLY
DLN-125
< DISASSEMBLY AND ASSEMBLY >
[FRONT FINAL DRIVE: F160A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
14. For proper reinstallation, paint matching marks on one differen-
tial case assembly.
CAUTION:
For matching marks, use paint. Do not damage differential
case and drive gear.
15. Remove drive gear mounting bolts.
16. Tap drive gear off differential case assembly with a soft hammer.
CAUTION:
Tap evenly all around to keep drive gear from bending.
17. Remove lock pin of pinion mate shaft with a punch from drive
gear side.
18. Remove pinion mate shaft.
19. Turn pinion mate gear, then remove pinion mate gears, pinion
mate thrust washers, side gears and side gear thrust washers
from differential case.
Assembly
INFOID:0000000000957361
PDIA0496E
PDIA0759J
SDIA0031J
SDIA0032J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст