Infiniti G35 (V35) Sedan. Manual — part 604
SPARK PLUG
EM-15
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
SPARK PLUG
Exploded View
INFOID:0000000000956229
Removal and Installation
INFOID:0000000000956230
REMOVAL
1.
Remove engine cover with power tool. Refer to
.
2.
Remove air cleaner case and air duct (RH and LH). Refer to
.
3.
Remove electric throttle control actuator. Refer to
.
4.
Remove ignition coil. Refer to
EM-45, "Removal and Installation"
.
1.
PCV hose
2.
Clamp
3.
Ignition coil
4.
Spark plug
5.
PCV valve
6.
O-ring
7.
Rocker cover gasket (right bank)
8.
Rocker cover (right bank)
9.
O-ring
10.
Camshaft position sensor (PHASE)
(bank 1)
11.
Exhaust valve timing control position
sensor (bank 1)
12.
Camshaft position sensor (PHASE)
(bank 2)
13.
Exhaust valve timing control position
sensor (bank 2)
14.
Rocker cover gasket (left bank)
15. Rocker cover (left bank)
16.
PCV hose
17.
Oil catcher
18. Oil filler cap
19.
PCV hose
A.
To intake manifold collector
B.
Refer to
C.
Camshaft bracket side
D.
To air duct
Refer to
for symbol marks in the figure.
JPBIA0009ZZ
EM-16
< ON-VEHICLE MAINTENANCE >
SPARK PLUG
5.
Remove spark plug with a spark plug wrench (commercial ser-
vice tool).
INSTALLATION
Installation is the reverse order of removal.
Inspection
INFOID:0000000000956231
INSPECTION AFTER REMOVAL
Use the standard type spark plug for normal condition.
CAUTION:
• Do not drop or shock spark plug.
• Do not use a wire brush for cleaning.
• If plug tip is covered with carbon, spark plug cleaner may be
used.
• Checking and adjusting plug gap is not required between
change intervals.
a
: 14 mm (0.55 in)
JPBIA0030ZZ
Spark plug (Standard type)
: Refer to
Cleaner air pressure:
Less than 588 kPa (6 kg/
cm
2
, 85 psi)
Cleaning time:
Less than 20 seconds
SMA773C
JPBIA0031ZZ
CAMSHAFT VALVE CLEARANCE
EM-17
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
CAMSHAFT VALVE CLEARANCE
Inspection and Adjustment
INFOID:0000000000956232
INSPECTION
Perform inspection as follows after removal, installation or replacement of camshaft or valve-related parts, or if
there is unusual engine conditions regarding valve clearance.
In cases of removing/installing or replacing camshaft and valve-
related parts, or of unusual engine conditions due to changes in
valve clearance (found malfunctions during stating, idling or causing
noise), perform inspection as follows:
1.
Remove rocker covers (right and left bank). Refer to
EM-45, "Removal and Installation"
.
2.
Measure the valve clearance as follows:
a.
Set No. 1 cylinder at TDC of its compression stroke.
• Rotate crankshaft pulley clockwise to align timing mark
(grooved line without color) with timing indicator.
• Make sure that intake and exhaust cam nose on No. 1 cylinder
(engine front side of right bank) are located as shown in the
figure.
• If not, turn crankshaft one revolution (360 degrees) and align
as shown in the figure.
b.
Use a feeler gauge, measure the clearance between valve lifter
and camshaft.
: Engine front
JPBIA0164ZZ
: Timing mark (grooved line without color)
JPBIA0043ZZ
: Engine front
JPBIA0044ZZ
Valve clearance
: Refer to
SEM139D
EM-18
< ON-VEHICLE MAINTENANCE >
CAMSHAFT VALVE CLEARANCE
• By referring to the figure, measure the valve clearances at
locations marked “
×
” as shown in the table below (locations
indicated in the figure).
• No. 1 cylinder at compression TDC
c.
Rotate crankshaft by 240 degrees clockwise (when viewed from engine front) to align No. 3 cylinder at
TDC its compression stroke.
NOTE:
To align cylinder No. 3 with the compression top dead center,
place matching marks (A) on the crankshaft pulley (1) side and
on the cylinder block side at a point 240
°
(b) counterclockwise
from the compression top dead center using the hex head of the
crankshaft pulley bolt as a guide.
: Engine front
Measuring position [right bank (A)]
No. 1 CYL.
No. 3 CYL.
No. 5 CYL.
No. 1 cylinder at com-
pression TDC
EXH (C)
×
(B)
INT (D)
×
(E)
Measuring position [left bank (H)]
No. 2 CYL.
No. 4 CYL.
No. 6 CYL.
No. 1 cylinder at com-
pression TDC
INT (D)
×
(F)
EXH (C)
×
(G)
JPBIA0165ZZ
JPBIA0166ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст