Infiniti G35 (V35) Sedan. Manual — part 602
PRECAUTIONS
EM-7
< PRECAUTION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
1.
Using a scraper (A), remove old liquid gasket adhering to the liq-
uid gasket application surface and the mating surface.
• Remove liquid gasket completely from the groove of the liquid
gasket application surface, mounting bolts, and bolt holes.
2.
Wipe the liquid gasket application surface and the mating sur-
face with white gasoline (lighting and heating use) to remove
adhering moisture, grease and foreign materials.
3.
Attach liquid gasket tube to the tube presser [SST: WS39930000
(
—
)].
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-15, "Recommended Chemical Products and Sealants"
.
4.
Apply liquid gasket without breaks to the specified location with
the specified dimensions.
• If there is a groove for liquid gasket application, apply liquid
gasket to the groove.
• As for bolt holes (B), normally apply liquid gasket inside the
holes. Occasionally, it should be applied outside the holes.
Make sure to read the text of this manual.
• Within five minutes of liquid gasket application, install the mat-
ing component.
• If liquid gasket protrudes, wipe it off immediately.
• Do not retighten mounting bolts or nuts after the installation.
• After 30 minutes or more have passed from the installation, fill
engine oil and engine coolant.
CAUTION:
If there are specific instructions in this manual, observe them.
JPBIA0053ZZ
EMA0622D
A
: Groove
: Inside
JPBIA0010ZZ
EM-8
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000000956221
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
KV10116200
(J26336-A)
Valve spring compressor
1. KV10115900
(J26336-20)
Attachment
2.KV10109220
(
—
)
Adapter
Disassembling valve mechanism
Part (1) is a component of KV10116200
(J26336-A), but Part (2) is not so.
KV10107902
(J38959)
Valve oil seal puller
Replacing valve oil seal
KV10115600
(J-38958)
Valve oil seal drift
Installing valve oil seal
Use side A (G).
a: 20 (0.79) dia. d: 8 (0.31) dia.
b: 13 (0.51) dia. e: 10.7 (0.421)
c: 10.3 (0.406) dia. f: 5 (0.20)
H: side B
Unit: mm (in)
EM03470000
(J8037)
Piston ring compressor
Installing piston assembly into cylinder bore
ST16610001
(J23907)
Pilot bushing puller
Removing pilot converter
KV10111100
(J37228)
Seal cutter
Removing oil pan (lower and upper), front and
rear timing chain case, etc.
PBIC1650E
NT011
JPBIA0396ZZ
NT044
NT045
NT046
PREPARATION
EM-9
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Commercial Service Tools
INFOID:0000000000956222
WS39930000
(
—
)
Tube presser
Pressing the tube of liquid gasket
KV10112100
(BT8653-A)
Angle wrench
Tightening bolts for connecting rod bearing
cap, cylinder head, etc. in angle
KV10114400
(J38365)
Heated oxygen sensor wrench
Loosening or tightening air fuel ratio sensor 1
a: 22 mm (0.87 in)
KV10118600
(J-48641)
Ring gear stopper
Removing and installing crankshaft pulley
—
(J-45488)
Quick connector release
Removing fuel tube quick connectors in en-
gine room
Tool number
(Kent-Moore No.)
Tool name
Description
NT052
NT014
JPBIA0397ZZ
JPBIA0409ZZ
PBIC0198E
EM-10
< PREPARATION >
PREPARATION
(Kent-Moore No.)
Tool name
Description
(
—
)
Power tool
Loosening nuts and bolts
(BT3373-F)
Belt tension gauge
Checking drive belt tension
(
—
)
TORX socket
Removing and installing drive plate
Size: T55
(
—
)
Manual lift table caddy
Removing and installing engine
(J24239-01)
Cylinder head bolt wrench
Loosening and tightening cylinder head bolt,
and used with the angle wrench [SST:
KV10112100 (BT8653-A)]
a: 13 (0.51) dia.
b: 12 (0.47)
c: 10 (0.39)
Unit: mm (in)
(
—
)
1.Compression gauge
2.Adapter
Checking compression pressure
(
—
)
Spark plug wrench
Removing and installing spark plug
a: 14 mm (0.55 in)
PBIC0190E
AMA126
PBIC1113E
ZZA1210D
JPBIA0398ZZ
ZZA0008D
JPBIA0399ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст