Infiniti G35 (V35) Sedan. Manual — part 1334
TM-28
< REMOVAL AND INSTALLATION >
[6MT: FS6R31A]
TRANSMISSION ASSEMBLY
g.
Remove guide plate mounting bolts and then remove control
lever assembly and control lever spring from control lever hous-
ing.
CAUTION:
Restrain guide plate while doing this because there is a
danger control lever assembly will fly out of control lever
housing.
7.
Remove clutch tube (1), clutch hose (2), and lock plate (3).
Refer to
CL-13, "Removal and Installation"
CAUTION:
• Keep painted surface on the body or other parts free of
clutch fluid. If it spills, wipe up immediately and wash the
affected area with water.
• Do not depress clutch pedal during removal procedure.
NOTE:
Insert a suitable plug into clutch hose and CSC (Concentric
Slave Cylinder) tube after removing clutch tube.
8.
Remove crankshaft position sensor (POS). Refer to
EM-114, "Disassembly and Assembly"
CAUTION:
• Handle carefully to avoid dropping and shocks.
• Do not disassemble.
• Do not allow metal powder to adhere to magnetic part at sensor tip.
• Do not place sensors in a location where they are exposed to magnetism.
9.
Remove starter motor. Refer to
STR-16, "Removal and Installation"
.
10. Remove rear plate cover. Refer to
.
11. Disconnect park/neutral position (PNP) switch harness connec-
tor.
12. Disconnect heated oxygen sensor 2 (bank 1) and heated oxy-
gen sensor 2 (bank 2) harness connectors. Refer to
13. Remove harness brackets.
14. Set a suitable jack to the transmission assembly.
CAUTION:
When setting a suitable jack, be careful so that it does not
contact with the switch.
15. Remove engine mounting insulator (rear) mounting nuts. Refer
EM-77, "2WD : Removal and Installation"
.
16. Remove rear engine mounting member. Refer to
.
17. Remove engine and transmission mounting bolts with power
tool.
18. Lower a suitable jack to the position where the back-up lamp
switch harness connector can be disconnect. Then disconnect back-up lamp switch harness connector.
19. Remove transmission assembly from the vehicle.
CAUTION:
JPDIC0022ZZ
: Vehicle front
JPDIC0026ZZ
JPDIC0024ZZ
JPDIC0023ZZ
TRANSMISSION ASSEMBLY
TM-29
< REMOVAL AND INSTALLATION >
[6MT: FS6R31A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Secure transmission assembly to a suitable jack while removing it.
• The transmission assembly must not interfere with the three way catalyst (right bank) and three
way catalyst (left bank).
• The transmission assembly must not interfere with the wire harnesses and clutch hose.
• Do not hold control lever housing to prevent bushing of control lever housing from deformation
when moving transmission assembly.
20. Remove CSC (Concentric Slave Cylinder) body and CSC tube. Refer to
CAUTION:
If transmission assembly is removed from the vehicle, always replace CSC (Concentric Slave Cyl-
inder) body and CSC tube. Return CSC body insert to original position to remove transmission
assembly. Dust on clutch disc sliding parts may damage seal of CSC body and may cause clutch
fluid leakage.
21. Remove dynamic damper. Refer to
EM-77, "2WD : Removal and Installation"
INSTALLATION
Note the following, and install in the reverse order of removal.
• Tighten transmission assembly mounting bolts to the specified
torque. The figure is the view from the vehicle forward.
CAUTION:
• The transmission assembly must not interfere with the three way catalyst (right bank) and three
way catalyst (left bank).
• The transmission assembly must not interfere with the wire harnesses and clutch hose.
• When installing transmission assembly, be careful not to bring main drive gear into contact with
clutch cover.
• Do not hold control lever housing to prevent bushing of control lever housing from deformation
when moving transmission assembly.
• Refer to
CL-15, "Removal and Installation"
for CSC (Concentric Slave Cylinder) body and CSC tube installa-
tion procedure.
• Refer to
CL-13, "Removal and Installation"
for clutch tube and clutch hose installation procedure.
• Refer to
TM-18, "Removal and Installation"
for control lever assembly installation procedure.
• After installation, check for oil leakage and oil level. Refer to
.
• If flywheel is removed, align dowel pin with the smallest hole of flywheel. Refer to
: Transmission to engine
: Engine to transmission
Bolt symbol
A
B
Quantity
8
4
“
” mm (in)
65 (2.56)
35 (1.38)
JPDIC0013ZZ
TM-30
< DISASSEMBLY AND ASSEMBLY >
[6MT: FS6R31A]
TRANSMISSION ASSEMBLY
DISASSEMBLY AND ASSEMBLY
TRANSMISSION ASSEMBLY
Exploded View
INFOID:0000000000956968
CASE AND EXTENSION
1.
Breather tube
2.
Bracket
3.
Filler plug
4.
Gasket
5.
Front cover oil seal
6.
Front cover
7.
Front cover gasket
8.
Transmission case
9.
Drain plug
10. Baffle plate
11.
Sliding ball bearing
12. Magnet
13. Dowel pin
14. Bushing
15. Mainshaft bearing retainer
16. Adapter plate
17. Oil gutter
A.
Seal lip
: Apply multi-purpose grease.
: Apply Genuine Silicone RTV or an equivalent. Refer to
GI-15, "Recommended Chemical Products and Sealants"
: Apply Genuine Medium Strength Thread Locking Sealant or an equivalent. Refer to
.
JPDIC0014GB
TRANSMISSION ASSEMBLY
TM-31
< DISASSEMBLY AND ASSEMBLY >
[6MT: FS6R31A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SHAFT AND GEAR
: For the bolt mounting positions, refer to
.
Refer to
for symbols not described on the above.
1.
Rear extension upper cover
2.
Rear extension upper cover gasket
3.
Bracket
4.
Sliding ball bearing
5.
Bushing
6.
Plunger
7.
Park/Neutral position (PNP) switch
8.
Rear extension oil gutter
9.
Cap
10. Rear extension
11.
Back-up lamp switch
12. Rear oil seal
13. Rear extension dust cover
14. Striking rod oil seal
15. Check ball
16. Check select spring
A.
Seal lip
: Apply multi-purpose grease.
: Apply Genuine Silicone RTV or an equivalent. Refer to
GI-15, "Recommended Chemical Products and Sealants"
Refer to
for symbols not described on the above.
JPDIC0015GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст