Infiniti G35 (V35) Sedan. Manual — part 1333
TM-24
< ON-VEHICLE REPAIR >
[6MT: FS6R31A]
AIR BREATHER HOSE
AIR BREATHER HOSE
Exploded View
INFOID:0000000000956964
Removal and Installation
INFOID:0000000000956965
REMOVAL
Refer to the figure for removal procedure.
INSTALLATION
Refer to the figure for installation procedure.
CAUTION:
• Make sure there are no pinched or restricted areas on the air breather hose caused by bending or
winding when installing it.
• Be sure to insert air breather hose into breather tube until
hose end reaches the tube's base.
• Be sure to insert air breather hose into breather until hose
end reaches the breather's base.
1.
Breather
2.
Bracket
3.
Water outlet (rear)
4.
Breather tube
5.
Air breather hose
: Vehicle front
JPDIC0011ZZ
SCIA2663J
AIR BREATHER HOSE
TM-25
< ON-VEHICLE REPAIR >
[6MT: FS6R31A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Set air breather hose with painted mark facing backward.
: Painted mark
JPDIC0030ZZ
TM-26
< REMOVAL AND INSTALLATION >
[6MT: FS6R31A]
TRANSMISSION ASSEMBLY
REMOVAL AND INSTALLATION
TRANSMISSION ASSEMBLY
Exploded View
INFOID:0000000000956966
CAUTION:
If transmission assembly is removed from the vehicle, always replace CSC (Concentric Slave Cylinder) body and CSC tube.
Return CSC body insert to original position to remove transmission assembly. Dust on clutch disc sliding parts may damage
seal of CSC body and may cause clutch fluid leakage.
Removal and Installation
INFOID:0000000000956967
CAUTION:
If transmission assembly is removed from the vehicle, always replace CSC (Concentric Slave Cylin-
der) body and CSC tube. Return CSC body insert to original position to remove transmission assem-
bly. Dust on clutch disc sliding parts may damage seal of CSC body and may cause clutch fluid
leakage.
REMOVAL
1.
Disconnect the battery cable from the negative terminal.
2.
Remove exhaust mounting bracket. Refer to
EX-5, "Removal and Installation"
.
3.
Remove suspension member stay. Refer to
FSU-20, "Removal and Installation"
4.
Remove exhaust front tube, center muffler, main muffler (RH), and main muffler (LH). Refer to
5.
Remove propeller shaft assembly. Refer to
DLN-86, "Removal and Installation"
.
NOTE:
Insert a suitable plug into rear oil seal of transmission assembly after removing propeller shaft assembly.
6.
Remove control lever assembly with the following procedure.
1.
Harness bracket
2.
Transmission assembly
: For the bolt mounting positions, refer to “INSTALLATION”.
JPDIC0012GB
TRANSMISSION ASSEMBLY
TM-27
< REMOVAL AND INSTALLATION >
[6MT: FS6R31A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
a.
Remove control rod mounting bolt and then separate control
lever assembly from control rod.
b.
Remove console finisher assembly as shown in the figure. Refer
to
IP-12, "Removal and Installation"
.
c.
Remove felt as shown in the figure.
d.
Remove center console assembly to remove hole cover as
shown in the figure. Refer to
IP-12, "Removal and Installation"
e.
Remove hole cover.
f.
Remove control lever boot B, hole insulator, and control lever
boot A.
SCIA1364E
JPDIC0018ZZ
JPDIC0019ZZ
JPDIC0020ZZ
JPDIC0021ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст