Infiniti G35 (V35) Sedan. Manual — part 707
FAX-28
< SERVICE DATA AND SPECIFICATIONS (SDS)
[AWD]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000000957496
Drive Shaft
INFOID:0000000000957497
Axial end play
0.05 mm (0.002 in) or less
Joint
Wheel side
Front final drive side
Grease quantity
Left side
77 – 97 g (2.72 – 3.42 oz)
95 – 105 g (3.35 – 3.70 oz)
Right side
113 – 123 g (3.99 – 4.34 oz)
Boots installed length
Left side
136 mm (5.35 in)
151.9 mm (5.98 in)
Right side
158 mm (6.22 in)
FL-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
FL
A
FL
N
O
P
CONTENTS
FUEL SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
General Precautions . . . . . . . . . . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tools . . . . . . . . . ....
ON-VEHICLE MAINTENANCE . . . . . .
FUEL SYSTEM . . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . . ..
Quick Connector . . . . . . . . . . . . . ...
ON-VEHICLE REPAIR . . . . . . . . ..
FUEL LEVEL SENSOR UNIT, FUEL FILTER
AND FUEL PUMP ASSEMBLY . . . . . . ..
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . . .
FUEL TANK . . . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
DISASSEMBLY AND ASSEMBLY . . . ..
FUEL LEVEL SENSOR UNIT, FUEL FILTER
AND FUEL PUMP ASSEMBLY . . . . . .
Exploded View . . . . . . . . . . . . . . .
Disassembly . . . . . . . . . . . . . . .
Assembly . . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
FL-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
General Precautions
INFOID:0000000000956364
WARNING:
When replacing fuel line parts, be sure to observe the following.
• Put a “CAUTION: FLAMMABLE” sign in the workshop.
• Be sure to work in a well ventilated area and furnish workshop with a CO
2
fire extinguisher.
• Do not smoke while servicing fuel system. Keep open flames and sparks away from the work area.
CAUTION:
• Use gasoline required by the regulations for octane number. Refer to
• Before removing fuel line parts, perform out the following procedures:
- Put drained fuel in an explosion-proof container and put the lid on securely. Keep the container in
safe area.
- Release fuel pressure from the fuel lines. Refer to
- Disconnect the battery cable from the negative terminal.
• Always replace O-ring and clamps with new ones.
• Do not kink or twist tubes when they are being installed.
• Do not tighten hose clamps excessively to avoid damaging hoses.
• After installing tubes, make sure there is no fuel leakage at connections in the following steps.
- Apply fuel pressure to fuel lines with turning ignition switch “ON” (with engine stopped). Then check
for fuel leaks at connections.
- Start engine and rev it up and check for fuel leaks at connections.
• Use only a genuine NISSAN fuel filler cap as a replacement. If an incorrect fuel filler cap is used, the
“MIL” may come on.
• For servicing “Evaporative Emission System” parts, refer to
EC-77, "Component Parts Location"
.
• For servicing “On Board Refueling Vapor Recovery (ORVR)” parts, refer to
.
PREPARATION
FL-3
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000000956365
Tool name
Description
Power tool
Loosening nuts and bolts
PBIC0190E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст