Infiniti G35 (V35) Sedan. Manual — part 708
FL-4
< ON-VEHICLE MAINTENANCE >
FUEL SYSTEM
ON-VEHICLE MAINTENANCE
FUEL SYSTEM
Inspection
INFOID:0000000000956366
Inspect fuel lines, fuel filler cap and fuel tank for improper attach-
ment, leaks, cracks, damage, loose connections, chafing or deterio-
ration.
If necessary, repair or replace damaged parts.
Quick Connector
INFOID:0000000000956367
CAUTION:
• After connecting fuel tube quick connectors, make sure quick
connectors are secure.
Ensure that connector and resin tube do not contact any adja-
cent parts.
A
: Engine
B
: Fuel line
C
: Fuel tank
JPBIA0129ZZ
1
: Quick connector
2
: Retainer
A
: Hard tube (or the equivalent)
B
: Connection (cross-section)
C
: Resin tube
D
: To under floor fuel line
E
: To fuel tank
F
: Tab
G
: Disconnection
JPBIA0130ZZ
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-5
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
ON-VEHICLE REPAIR
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
Exploded View
INFOID:0000000000956368
Removal and Installation
INFOID:0000000000956369
WARNING:
Read “General Precautions” when working on the fuel system. Refer to
REMOVAL
1.
Check fuel level on fuel gauge. If fuel gauge indicates more than
the level as shown in the figure (full or almost full), drain fuel
from fuel tank until fuel gauge indicates level as shown in the fig-
ure or below.
NOTE:
Because fuel will be spilled when removing main and sub fuel
level sensor units for the top of the fuel is above the main and
sub fuel level sensor units installation surface.
• As a guide, fuel level becomes the position as shown in the
figure or below when approximately 20 (5-1/4 US gal, 4-3/8
Imp gal) of fuel are drained from fuel tank.
• In a case that fuel pump does not operate, perform the follow-
ing procedure.
1.
Retainer
2.
Main fuel level sensor unit, fuel filter
and fuel pump assembly
3.
O-ring
4.
Sub fuel level sensor unit
A.
Right side
B.
Left side
Refer to
for symbol marks in the figure.
JPBIA0154GB
JPBIA0131ZZ
FL-6
< ON-VEHICLE REPAIR >
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
a.
Insert hose of less than 25 mm (0.98 in) in diameter into fuel filler tube through fuel filler opening to draw
fuel from fuel filler tube.
b.
Disconnect fuel filler hose from fuel filler tube. Refer to
c.
Insert fuel tube into fuel tank through fuel filler hose to draw fuel from fuel tank.
2.
Release the fuel pressure from the fuel lines. Refer to
3.
Open fuel filler lid.
4.
Open filler cap and release the pressure inside fuel tank.
5.
Remove rear seat cushion. Refer to
.
6.
Peel off floor carpet, then remove inspection hole cover (1) units
by turning clips (2) clockwise by 90 degrees.
7.
Disconnect harness connector (3) and fuel feed tube (2).
Disconnect quick connector as follows:
• Hold the sides of connector, push in tabs and pull out fuel feed
tube.
• If quick connector sticks to tube of main fuel level sensor unit,
push and pull quick connector several times until they start to
move.Then disconnect them by pulling.
CAUTION:
Right side
: Main fuel level sensor unit, fuel filter
and fuel pump assembly
Left side
: Sub fuel level sensor unit
A
: Direction mark
b
: 90
°
: Vehicle front
1
: Quick connector
: Vehicle front
JPBIA0132ZZ
JPBIA0133ZZ
A
: Pull
B
: Push in tabs
JPBIA0134ZZ
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-7
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
• Quick connector (1) can be disconnected when the tabs
(F) are completely depressed. Do not twist it more than
necessary.
• Do not use any tools to disconnected quick connector.
• Keep resin tube (C) away from heat. Be especially careful
when welding near the resin tube.
• Prevent acid liquid such as battery electrolyte, etc. from
getting on resin tube.
• Do not bend or twist resin tube during installation and dis-
connection.
• Do not remove the remaining retainer (2) on hard tube (or
the equivalent) (A) except when resin tube or retainer is
replaced.
• When resin tube or hard tube (or the equivalent) is
replaced, also replace retainer with new one.
• To keep the connecting portion clean and to avoid dam-
age and foreign materials, cover them completely with
plastic bags (A) or something similar.
8.
Remove main fuel level sensor unit, fuel filter and fuel pump assembly, and sub fuel level sensor unit as
follows:
CAUTION:
• Do not bend float arm during removal.
• Avoid impacts such as falling when handling components.
a.
Removal of main fuel level sensor unit, fuel filter and fuel pump assembly:
i.
Remove retainer.
ii.
Raise main fuel level sensor unit, fuel filter and fuel pump
assembly, and using snap ring pliers (A), remove fuel hose con-
nector (1).
CAUTION:
Be careful not to damage fuel hose connector by expanding
them excessively.
b.
Removal of sub fuel level sensor unit:
i.
Remove retainer.
ii.
Raise and release sub fuel level sensor unit to remove.
INSTALLATION
Note to the following, and install in the reverse order of removal.
Fuel hose
B
: Connection (Cross-section)
D
: To under floor fuel line
E
: To fuel tank
G
: Disconnection
Retainer color: Green
JPBIA0130ZZ
JPBIA0135ZZ
2
: Fuel hose
JPBIA0136ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст