Infiniti G35 (V35) Sedan. Manual — part 755
HA-54
< ON-VEHICLE REPAIR >
CONDENSER PIPE ASSEMBLY
CONDENSER PIPE ASSEMBLY
Exploded View
INFOID:0000000000959882
Removal and Installation
INFOID:0000000000959883
REMOVAL
1.
Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2.
Remove front bumper.
EXT-11, "Removal and Installation"
.
3.
Remove air cleaner case (LH) and air duct (LH). Refer to
EM-25, "Removal and Installation"
4.
Disconnect the one-touch joint between high-pressure flexible
hose (1) and condenser pipe assembly (2) with disconnector (A)
(SST: 9253089912).
CAUTION:
Cap or wrap the joint of high-pressure flexible hose and
condenser pipe assembly with suitable material such as
vinyl tape to avoid the entry of air.
5.
Disconnect the one-touch joints between high-pressure pipe 1
(3) and condenser pipe assembly with disconnector (A) (SST:
9253089908).
CAUTION:
Cap or wrap the joint of high-pressure pipe 1 and con-
denser pipe assembly with suitable material such as vinyl tape to avoid the entry of air.
1.
Refrigerant pressure sensor
2.
O-ring
3.
Liquid tank bracket
4.
Liquid tank
5.
Bracket
6.
Condenser pipe assembly
7.
Radiator & condenser assembly
JSIIA0012GB
JSIIA0095ZZ
CONDENSER PIPE ASSEMBLY
HA-55
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
6.
Remove mounting bolt (A) from condenser pipe assembly (1).
7.
Remove mounting bolt (A) from condenser pipe assembly (1).
8.
Remove condenser pipe assembly.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-rings of condenser pipe assembly, high-pressure flexible hose and high-pressure pipe 1
with new ones, and then apply compressor oil to it when installing it.
• Female-side piping connection is thin and easy to deform. Slowly insert the male-side piping
straight in axial direction.
• Insert piping securely until a click is heard.
• After piping connection is completed, pull male-side piping by hand to make sure that connection
does not come loose.
• When recharging refrigerant, check for leaks.
JSIIA0088ZZ
JSIIA0030ZZ
HA-56
< ON-VEHICLE REPAIR >
LIQUID TANK
LIQUID TANK
Exploded View
INFOID:0000000000959884
Removal and Installation
INFOID:0000000000959885
REMOVAL
1.
Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2.
Remove front grille. Refer to
EXT-16, "Removal and Installation"
.
3.
Clean liquid tank and its surrounding area, and remove dust and rust from liquid tank.
CAUTION:
Be sure to clean carefully.
4.
Remove mounting bolts (A) from liquid tank (1).
5.
Remove liquid tank.
INSTALLATION
Install liquid tank, and then install liquid tank bracket on condenser.
CAUTION:
• Make sure liquid tank bracket is securely installed at protrusion of condenser. (Make sure liquid tank
bracket does not move to a position below center of liquid tank.)
• Replace O-rings of A/C piping with new ones, and then apply compressor oil to it when installing it.
• When recharging refrigerant, check for leaks.
1.
Refrigerant pressure sensor
2.
O-ring
3.
Liquid tank bracket
4.
Liquid tank
5.
Bracket
6.
Condenser pipe assembly
7.
Radiator & condenser assembly
JSIIA0012GB
JSIIA0094ZZ
REFRIGERANT PRESSURE SENSOR
HA-57
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
REFRIGERANT PRESSURE SENSOR
Exploded View
INFOID:0000000000959886
Removal and Installation
INFOID:0000000000959887
REMOVAL
1.
Remove liquid tank. Refer to
HA-56, "Removal and Installation"
.
2.
Fix the liquid tank (1) with a vise (A). Remove the refrigerant
pressure sensor (2) with a wrench (B).
CAUTION:
Be careful not to damage liquid tank.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Apply compressor oil to O-ring of refrigerant pressure sensor when installing it.
• When recharging refrigerant, check for leaks.
1.
Refrigerant pressure sensor
2.
O-ring
3.
Liquid tank bracket
4.
Liquid tank
5.
Bracket
6.
Condenser pipe assembly
7.
Radiator & condenser assembly
JSIIA0012GB
JSIIA0075ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст