Infiniti G35 (V35) Sedan. Manual — part 825
INT-24
< ON-VEHICLE REPAIR >
HEADLINING
7.
Remove mounting plastic clips (A) using a screwdriver (B) of
front and rear assistance grips (1), and then remove assist grips.
8.
Remove rear seat cushion and seatback. Refer to
SE-105, "Removal and Installation"
9.
Remove front kicking plate inner, center pillar lower garnish, center pillar upper garnish, rear kicking plate
inner, rear wheelhouse garnish, rear pillar finisher. Refer to
INT-13, "Removal and Installation"
10. Disconnect antenna feeder connectors (A) of antenna amplifier
and sub-antenna feeder after removing rear pillar finisher (LH),
and then remove antenna feeder securing clip (B) with a
remover tool.
11. Remove passenger seat assembly. Refer to
SE-95, "Removal and Installation"
12. With a removal tool, remove body side mounting plastic clip from rear end of headlining.
13. Pull map lamp assembly toward vehicle lower, and disengage
dual-lock fastener (A) and metal clips (B).
CAUTION:
Map lamp assembly is crimped from back of headlining.
Remove it by disengaging the crimped area of back of map
lamp assembly after removing headlining from the vehicle.
14. Remove headlining from rear door left opening.
CAUTION:
• When removing, 2 workers are required. (1 for the front
and rear of headlining)
• Cover center console finisher upper surface with a shop
cloth to prevent it from being damaged.
• Do not bend headlining when removing.
15. Remove the following parts after removing headlining.
• Personal lamp (LH/RH). Refer to
INL-101, "Removal and Installation"
.
• Map lamp assembly (without LDW system). Refer to
INL-96, "Removal and Installation"
• Roof harness assembly.
• Antenna feeder assembly.
JMJIA0096GB
: Clip
JMJIA0095GB
JMJIA0099GB
JMJIA0100GB
HEADLINING
INT-25
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Install headlining assembly after inserting clips to clip holder of headlining rear end.
• Do not bend headlining when installing.
INT-26
< ON-VEHICLE REPAIR >
TRUNK ROOM TRIM & TRUNK LID FINISHER
TRUNK ROOM TRIM & TRUNK LID FINISHER
Exploded View
INFOID:0000000000960444
TRUNK ROOM TRIM
TRUNK LID FINISHER INNER
1.
Trunk floor carpet
2.
Trunk center box
3.
Trunk floor felt
4.
Trunk front finisher upper
5.
Trunk rear plate
6.
Rear wheel house finisher (RH)
7.
Rear wheel house finisher (LH)
8.
Trunk front finisher
9.
Trunk net
Metal clip
JMJIA0108ZZ
TRUNK ROOM TRIM & TRUNK LID FINISHER
INT-27
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Removal and Installation
INFOID:0000000000960445
REMOVAL
TRUNK ROOM TRIM
1.
Fully open trunk lid assembly.
2.
Remove trunk weather-strip.
3.
Remove trunk floor carpet.
4.
Remove trunk floor felt.
5.
Remove trunk floor box.
6.
Remove trunk rear plate mounting metal clips, and then remove trunk rear plate.
7.
Remove trunk front upper finisher mounting clips, and then remove trunk front upper finisher.
8.
Remove trunk side finisher mounting clips, and then remove trunk side finisher (LH/RH).
9.
Remove trunk front finisher mounting clips, and then remove trunk front finisher.
10. Remove rear seat cushion and rear seatback. Refer to
SE-105, "Removal and Installation"
.
TRUNK LID FINISHER INNER
1.
Fully open trunk lid assembly.
2.
Remove trunk lid bumper rubber.
1.
Trunk lid bumper rubber
2.
Trunk lid pull handle
3.
Emergency handle
4.
Trunk lid finisher inner
5.
Trunk lid
JMJIA0072GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст