Infiniti G35 (V35) Sedan. Manual — part 824
INT-20
< ON-VEHICLE REPAIR >
FLOOR TRIM
FLOOR TRIM
Exploded View
INFOID:0000000000960440
Removal and Installation
INFOID:0000000000960441
REMOVAL
1.
Remove front seat (LH/RH) and rear seat cushion. Refer to
SE-105, "Removal and Installation"
.
2.
Remove accelerator pedal pad. Refer to
ACC-3, "Removal and Installation"
.
3.
Disengage clip of floor hook (1) with remover tool (A).
4.
Remove foot grille. Refer to
VTL-50, "FOOT GRILLES : Removal and Installation"
1.
Floor hook
2.
Floor trim
3.
Fixing clip
4.
Rear floor spacer (RH)
5.
Rear floor spacer (LH)
6.
Front floor spacer (LH)
7.
Front floor spacer (RH)
8.
Footrest
JMJIA0069GB
: Clip
JMJIA0092GB
FLOOR TRIM
INT-21
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
5.
Remove front seat belt floor anchor bolt (LH/RH). Refer to
SB-5, "SEAT BELT RETRACTOR : Removal
6.
Remove center console. Refer to
IP-12, "Removal and Installation"
7.
Remove floor duct.
• Refer to
VTL-53, "REAR FLOOR DUCT 1 (WITHOUT REAR VENTILATOR) : Removal and Installation"
.
(without REAR VENTILATOR)
• Refer to
VTL-54, "REAR FLOOR DUCT 1 & REAR VENTILATOR DUCT 1(WITH REAR VENTILATOR)
. (with REAR VENTILATOR)
8.
Remove instrument lower cover and instrument driver panel, instrument assist lower panel. Refer to
12, "Removal and Installation"
9.
Remove instrument side panel (LH/RH). Refer to
IP-12, "Removal and Installation"
10. Remove G-sensor (1). Refer to
.
11. Remove diagnosis sensor unit (2). Refer to
12. Remove floor harness mounting clamps (A).
13. Remove console rear bracket (3). Refer to
.
14. Remove dash side finisher, front kicking plate inner, center pillar lower garnish, and rear kicking plate
inner, front body side welt (LH/RH), rear body side welt (LH/RH). Refer to
INT-13, "Removal and Installa-
15. Remove floor trim mounting clips and fixing nuts.
16. Remove floor trim from floor trim fixing clips (A) and remove floor
carpet (1).
INSTALLATION
Install in the reverse order of removal.
JMJIA0093GB
JMJIA0094GB
INT-22
< ON-VEHICLE REPAIR >
HEADLINING
HEADLINING
Exploded View
INFOID:0000000000960442
1.
Sun visor holder
2.
Sun visor cover
3.
Sun visor assembly
4.
Roof front finisher
5.
Assist grip
6.
Personal lamp finisher
7.
Personal lamp lens
8.
Headlining (without SUNROOF)
9.
Antenna feeder
10. Map lamp assembly
11. Roof harness
12. Dual lock fastener
13. Map lamp lens
14. Headlining (with SUNROOF)
15. Roof bracket
16. Roof plate assembly
17. Personal lamp assembly
18. Rear hidden clip
19. Assist grip clip
JMJIA0070GB
HEADLINING
INT-23
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Removal and Installation
INFOID:0000000000960443
REMOVAL
1.
Remove front body side welt (LH/RH). Refer to
INT-13, "Removal and Installation"
2.
Remove front pillar garnish (LH/RH). Refer to
INT-13, "Removal and Installation"
.
3.
Remove antenna feeder securing clips with a remover tool after
removing front pillar garnish (LH), then disconnect antenna
feeder connectors (A).
4.
Remove front roof finisher mounting metal clips and pawls, and
then remove front roof finisher (1).
5.
Remove sun visor assembly (LH/RH).
• Remove sun visor cover.
• Remove sun visor assembly mounting screws.
• Disconnect vanity mirror lamp harness connectors.
6.
Rotate 45 degrees and remove sun visor holder (1) (LH/RH).
Pawl
Metal clip
: Clip
JMJIA0101GB
: Pawl
: Metal clip
JMJIA0097GB
JMJIA0098GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст