Infiniti G35 (V35) Sedan. Manual — part 309
CL-6
< ON-VEHICLE MAINTENANCE >
CLUTCH FLUID
CLUTCH FLUID
Air Bleeding Procedure
INFOID:0000000000956924
CAUTION:
• Monitor clutch fluid level in reservoir tank to make sure it does not empty.
• Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately
and wash the affected area with water.
NOTE:
Do not use a vacuum assist or any other type of power bleeder on this system. Use of vacuum assist or power
bleeder will not purge all the air from the system.
1.
Fill master cylinder reservoir tank with new clutch fluid.
2.
Connect a transparent vinyl hose to air bleeder valve.
3.
Depress clutch pedal slowly and fully several times at an interval
of 2 to 3 seconds and hold it.
4.
With clutch pedal depressed, open air bleeder valve to release
air.
5.
Close air bleeder valve.
6.
Release clutch pedal and wait for 5 seconds.
7.
Repeat steps 3 to 6 until no bubbles can be observed in clutch
fluid.
8.
Tighten air bleeder valve to the specified torque. Refer to
JPDIB0006ZZ
CLUTCH PEDAL
CL-7
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
ON-VEHICLE REPAIR
CLUTCH PEDAL
Exploded View
INFOID:0000000000956925
Removal and Installation
INFOID:0000000000956926
REMOVAL
1.
Remove front kicking plate inner and dash side finisher. Refer to
INT-13, "Removal and Installation"
.
2.
Remove instrument driver lower panel. Refer to
IP-12, "Removal and Installation"
.
3.
Remove bracket (1) and harness bracket (2).
4.
Disconnect ASCD clutch switch and clutch interlock switch har-
ness connectors and then disconnect clip of harness from clutch
pedal assembly.
5.
Remove snap pin and clevis pin.
6.
Remove clutch pedal assembly.
INSTALLATION
1.
ASCD clutch switch
2.
Clevis pin
3.
Bushing
4.
Stopper rubber
5.
Pedal pad
6.
Pedal stopper rubber
7.
Snap pin
8.
Clutch interlock switch
9.
Clutch pedal assembly
: Apply lithium-based grease including molybdenum disulphide.
: Refer to
for the tightening torque.
Refer to
for symbols not described on the above.
JPDIB0004GB
JPDIB0005ZZ
CL-8
< ON-VEHICLE REPAIR >
CLUTCH PEDAL
Note the following, and install in the reverse order of removal.
• After installing clutch interlock switch, adjust the switch position. Refer to
CL-5, "Inspection and Adjustment"
.
• Tighten lock nut of ASCD clutch switch to the specified torque after installing clutch pedal assembly and
adjusting the pedal free play. Refer to
CL-5, "Inspection and Adjustment"
.
Inspection
INFOID:0000000000956927
INSPECTION AFTER REMOVAL
Check clutch pedal for bend, damage, or a cracked weld. If bend, damage, or a cracked weld is found, replace
clutch pedal assembly.
CLUTCH MASTER CYLINDER
CL-9
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
CLUTCH MASTER CYLINDER
Exploded View
INFOID:0000000000956928
Removal and Installation
INFOID:0000000000956929
REMOVAL
CAUTION:
Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately
and wash the affected area with water.
1.
Remove front kicking plate inner and dash side finisher. Refer to
INT-13, "Removal and Installation"
.
2.
Remove instrument driver lower panel. Refer to
IP-12, "Removal and Installation"
.
3.
Remove snap pin and clevis pin from clevis and then separate it from clutch pedal assembly.
4.
Remove brake master cylinder cover. Refer to
EXT-18, "Removal and Installation"
5.
Drain clutch fluid in reservoir tank and then remove hose and clips.
1.
Reservoir tank assembly
2.
Hose
3.
Cylinder body
4.
Packing
5.
Clutch pedal assembly
6.
Return spring
7.
Piston assembly
8.
Push rod
9.
Stopper ring
10.
Boot
11.
Clevis
12. Snap pin
13.
Clevis pin
1: Apply rubber lubricant.
2: Apply silicone grease.
3: Apply lithium-based grease including molybdenum disulphide.
Refer to
for symbols not described on the above.
JPDIB0007GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст