Infiniti G35 (V35) Sedan. Manual — part 265
REPAIRING HIGH STRENGTH STEEL
BRM-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
• When welding HSS panels, use spot welding whenever possi-
ble in order to minimize weakening surrounding areas due to
heat.
If spot welding is impossible, use MIG. welding. Do not use
gas (torch) for welding because it is inferior in welding
strength.
• The spot weld on HSS panels is harder than that of an ordi-
nary steel panel.
Therefore, when cutting spot welds on a HSS panel, use a low
speed high torque drill (1,000 to 1,200 rpm) to increase drill bit
durability and facilitate the operation.
2.
Precautions in spot welding HSS
This work should be performed under standard working condi-
tions. Always note the following when spot welding HSS:
• The electrode tip diameter must be sized properly according to
the metal thickness.
• The panel surfaces must fit flush to each other, leaving no
gaps.
PIIA0144E
PIIA0145E
PIIA0146E
PIIA0147E
BRM-30
< REMOVAL AND INSTALLATION >
REPAIRING HIGH STRENGTH STEEL
• Follow the specifications for the proper welding pitch.
Unit: mm (in)
Thickness (t)
Minimum pitch (l)
0.6 (0.024)
0.8 (0.031)
1.0 (0.039)
1.2 (0.047)
1.6 (0.063)
1.8 (0.071)
10 (0.39) or over
12 (0.47) or over
18 (0.71) or over
20 (0.79) or over
27 (1.06) or over
31 (1.22) or over
PIIA0148E
REPLACEMENT OPERATIONS
BRM-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
REPLACEMENT OPERATIONS
Description
INFOID:0000000000961836
• This section is prepared for technicians who have attained a high level of skill and experience in repairing
collision-damaged vehicles and also use modern service tools and equipment. Persons unfamiliar with body
repair techniques should not attempt to repair collision-damaged vehicles by using this section.
• Technicians are also encouraged to read Body Repair Manual (Fundamentals) in order to ensure that the
original functions and quality of the vehicle can be maintained. The Body Repair Manual (Fundamentals)
contains additional information, including cautions and warning, that are not including in this manual. Techni-
cians should refer to both manuals to ensure proper repairs.
• Please note that these information are prepared for worldwide usage, and as such, certain procedures might
not apply in some regions or countries.
The symbols used in this section for welding operations are shown below.
Symbol marks
Description
2-spot welds
3-spot welds
MIG plug weld
For 3 panels plug weld method
MIG seam weld / Point weld
JSKIA0049ZZ
JSKIA0053ZZ
JSKIA0050ZZ
JSKIA0051ZZ
JSKIA0054ZZ
JSKIA0055ZZ
JSKIA0052ZZ
JSKIA0056ZZ
BRM-32
< REMOVAL AND INSTALLATION >
REPLACEMENT OPERATIONS
• Front pillar butt joint can be determined anywhere within shaded
area as shown in the figure. The best location for the butt joint is at
position A due to the construction of the vehicle. Refer to the front
pillar section.
• Determine cutting position and record distance from the locating
indent. Use this distance when cutting the service part. Cut outer
front pillar over 60 mm (2.36 in) above inner front pillar cut position.
• Prepare a cutting jig to make outer pillar easier to cut. Also, this will
permit service part to be accurately cut at joint position.
• An example of cutting operation using a cutting jig is as follows.
1.
Mark cutting lines.
A: Cut position of outer pillar
B: Cut position of inner pillar
2.
Align cutting line with notch on jig. Clamp jig to pillar.
3.
Cut outer pillar along groove of jig (at position A).
4.
Remove jig and cut remaining portions.
5.
Cut inner pillar at position B in same manner.
Radiator Core Support
INFOID:0000000000961837
PIIA0150E
PIIA0151E
PIIA0152E
PIIA0153E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст